 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Advance Information MPC7455EC/D Rev. 2, 1/2003 MPC7455 RISC Microprocessor Hardware Specifications This document is primarily concerned with the MPC7455; however, unless otherwise noted, all information here also applies to the MPC7445. The MPC7455 and MPC7445 are reduced instruction set computing (RISC) microprocessors that implement the PowerPC instruction set architecture. This document describes pertinent electrical and physical characteristics of the MPC7455. For functional characteristics of the processor, refer to the MPC7450 RISC Microprocessor Family User's Manual. This document contains the following topics: Topic Section 1.1, "Overview" Section 1.2, "Features" Page 1 2 Section 1.3, "Comparison with the MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441" 7 Section 1.4, "General Parameters" Section 1.5, "Electrical and Thermal Characteristics" Section 1.6, "Pin Assignments" Section 1.7, "Pinout Listings" Section 1.8, "Package Description" Section 1.9, "System Design Information" Section 1.10, "Document Revision History" Section 1.11, "Ordering Information" To locate any published updates for this document, refer to the website at http://www.motorola.com/semiconductors. 10 10 33 35 41 45 58 60 1.1 Overview The MPC7455 is the third implementation of the fourth generation (G4) microprocessors from Motorola. The MPC7455 implements the full PowerPC 32-bit architecture and is targeted at networking and computing systems applications. The MPC7455 consists of a processor core, a 256-Kbyte L2, and an internal L3 tag and controller which support a glueless backside L3 cache through a dedicated high-bandwidth interface. The MPC7445 is identical to the MPC7455 except it does not support the L3 cache interface. Features Figure 1 shows a block diagram of the MPC7455. The core is a high-performance superscalar design supporting a double-precision floating-point unit and a SIMD multimedia unit. The memory storage subsystem supports the MPX bus interface to main memory and other system resources. The L3 interface supports 1 or 2 Mbytes of external SRAM for L3 cache data. Note that the MPC7455 is footprint-compatible with the MPC7450 and MPC7451, and the MPC7445 is footprint-compatible with the MPC7441. 1.2 Features This section summarizes features of the MPC7455 implementation of the PowerPC architecture. Major features of the MPC7455 are as follows: * High-performance, superscalar microprocessor -- As many as four instructions can be fetched from the instruction cache at a time -- As many as three instructions can be dispatched to the issue queues at a time -- As many as 12 instructions can be in the instruction queue (IQ) -- As many as 16 instructions can be at some stage of execution simultaneously -- Single-cycle execution for most instructions -- One instruction per clock cycle throughput for most instructions -- Seven-stage pipeline control * Eleven independent execution units and three register files -- Branch processing unit (BPU) features static and dynamic branch prediction - 128-entry (32-set, four-way set-associative) branch target instruction cache (BTIC), a cache of branch instructions that have been encountered in branch/loop code sequences. If a target instruction is in the BTIC, it is fetched into the instruction queue a cycle sooner than it can be made available from the instruction cache. Typically, a fetch that hits the BTIC provides the first four instructions in the target stream. - 2048-entry branch history table (BHT) with two bits per entry for four levels of prediction--not-taken, strongly not-taken, taken, and strongly taken - Up to three outstanding speculative branches - Branch instructions that do not update the count register (CTR) or link register (LR) are often removed from the instruction stream. - Eight-entry link register stack to predict the target address of Branch Conditional to Link Register (bclr) instructions -- Four integer units (IUs) that share 32 GPRs for integer operands - Three identical IUs (IU1a, IU1b, and IU1c) can execute all integer instructions except multiply, divide, and move to/from special-purpose register instructions - IU2 executes miscellaneous instructions including the CR logical operations, integer multiplication and division instructions, and move to/from special-purpose register instructions 2 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Instruction Unit Branch Processing Unit Fetcher Tags IBAT Array BHT (2048-Entry) Dispatch Unit Data MMU SRs (Original) VR Issue (4-Entry/2-Issue) DBAT Array GPR Issue (6-Entry/3-Issue) FPR Issue (2-Entry/1-Issue) 128-Entry DTLB Tags LR BTIC (128-Entry) CTR Instruction Queue (12-Word) SRs (Shadow) 128-Entry ITLB Instruction MMU 128-Bit (4 Instructions) MOTOROLA 32-Kbyte I Cache 32-Kbyte D Cache Reservation Stations (2-Entry) EA Load/Store Unit Vector Touch Engine + (EA Calculation) Finished Stores L1 Castout PA FPR File 16 Rename Buffers Reservation Stations (2) VR File 16 Rename Buffers Integer Unit 2 Integer Integer Integer Unit 122 Unit Unit (3) +++ 32-Bit 32-Bit x/ 16 Rename Buffers Reservation Stations (2) GPR File Reservation Reservation Reservation Station Station Station Vector Touch Queue Vector Integer Unit 1 Vector FPU FloatingPoint Unit L1 Push Completed Stores +x/ FPSCR Load Miss 64-Bit 64-Bit 32-Bit 128-Bit 128-Bit L3 Cache Controller Line Block 0/1 Tags Status L3CR Bus Accumulator Not in MPC7445 18-Bit 64-Bit Data Address (8-Bit Parity) Memory Subsystem System Bus Interface L2 Prefetch (3) Bus Store Queue Push Castout Queue (9) External SRAM (1 or 2 Mbytes) Bus Accumulator 36-Bit Address Bus 64-Bit Data Bus L2 Store Queue (L2SQ) Snoop Push/ Interventions L1 Castouts (4) 256-Kbyte Unified L2 Cache/Cache Controller Line Block 0 (32-Byte) Block 1 (32-Byte) Tags Status Status L1 Service Queues L1 Store Queue (LSQ) L1 Load Queue (LLQ) L1 Load Miss (5) Instruction Fetch (2) Cacheable Store Request (1) Additional Features * Time Base Counter/Decrementer * Clock Multiplier * JTAG/COP Interface * Thermal/Power Management * Performance Monitor 96-Bit (3 Instructions) Reservation Reservation Reservation Reservation Station Station Station Station Figure 1. MPC7455 Block Diagram Vector Permute Unit Vector Integer Unit 2 Completion Unit MPC7455 RISC Microprocessor Hardware Specifications Completion Queue (16-Entry) Features Completes up to three instructions per clock 3 Features -- Five-stage FPU and a 32-entry FPR file - Fully IEEE 754-1985-compliant FPU for both single- and double-precision operations - Supports non-IEEE mode for time-critical operations - Hardware support for denormalized numbers - Thirty-two 64-bit FPRs for single- or double-precision operands -- Four vector units and 32-entry vector register file (VRs) - Vector permute unit (VPU) - Vector integer unit 1 (VIU1) handles short-latency AltiVec integer instructions, such as vector add instructions (vaddsbs, vaddshs, and vaddsws, for example) - Vector integer unit 2 (VIU2) handles longer-latency AltiVec integer instructions, such as vector multiply add instructions (vmhaddshs, vmhraddshs, and vmladduhm, for example) - Vector floating-point unit (VFPU) -- Three-stage load/store unit (LSU) - Supports integer, floating-point, and vector instruction load/store traffic - Four-entry vector touch queue (VTQ) supports all four architected AltiVec data stream operations - Three-cycle GPR and AltiVec load latency (byte, half-word, word, vector) with one-cycle throughput - Four-cycle FPR load latency (single, double) with one-cycle throughput - No additional delay for misaligned access within double-word boundary - Dedicated adder calculates effective addresses (EAs) - Supports store gathering - Performs alignment, normalization, and precision conversion for floating-point data - Executes cache control and TLB instructions - Performs alignment, zero padding, and sign extension for integer data - Supports hits under misses (multiple outstanding misses) - Supports both big- and little-endian modes, including misaligned little-endian accesses * Three issue queues FIQ, VIQ, and GIQ can accept as many as one, two, and three instructions, respectively, in a cycle. Instruction dispatch requires the following: -- Instructions can be dispatched only from the three lowest IQ entries--IQ0, IQ1, and IQ2 -- A maximum of three instructions can be dispatched to the issue queues per clock cycle -- Space must be available in the CQ for an instruction to dispatch (this includes instructions that are assigned a space in the CQ but not in an issue queue) * Rename buffers -- 16 GPR rename buffers -- 16 FPR rename buffers -- 16 VR rename buffers * Dispatch unit -- Decode/dispatch stage fully decodes each instruction 4 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Features * Completion unit -- The completion unit retires an instruction from the 16-entry completion queue (CQ) when all instructions ahead of it have been completed, the instruction has finished execution, and no exceptions are pending. -- Guarantees sequential programming model (precise exception model) -- Monitors all dispatched instructions and retires them in order -- Tracks unresolved branches and flushes instructions after a mispredicted branch -- Retires as many as three instructions per clock cycle * Separate on-chip L1 instruction and data caches (Harvard architecture) -- 32-Kbyte, eight-way set-associative instruction and data caches -- Pseudo least-recently-used (PLRU) replacement algorithm -- 32-byte (eight-word) L1 cache block -- Physically indexed/physical tags -- Cache write-back or write-through operation programmable on a per-page or per-block basis -- Instruction cache can provide four instructions per clock cycle; data cache can provide four words per clock cycle -- Caches can be disabled in software -- Caches can be locked in software -- MESI data cache coherency maintained in hardware -- Separate copy of data cache tags for efficient snooping -- Parity support on cache and tags -- No snooping of instruction cache except for icbi instruction -- Data cache supports AltiVec LRU and transient instructions -- Critical double- and/or quad-word forwarding is performed as needed. Critical quad-word forwarding is used for AltiVec loads and instruction fetches. Other accesses use critical double-word forwarding. * Level 2 (L2) cache interface -- On-chip, 256-Kbyte, eight-way set-associative unified instruction and data cache -- Fully pipelined to provide 32 bytes per clock cycle to the L1 caches -- A total nine-cycle load latency for an L1 data cache miss that hits in L2 -- PLRU replacement algorithm -- Cache write-back or write-through operation programmable on a per-page or per-block basis -- 64-byte, two-sectored line size -- Parity support on cache * Level 3 (L3) cache interface (not implemented on MPC7445) -- Provides critical double-word forwarding to the requesting unit -- Internal L3 cache controller and tags -- External data SRAMs -- Support for 1- and 2-Mbyte L3 caches MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 5 Features -- Cache write-back or write-through operation programmable on a per-page or per-block basis -- 64-byte (1M) or 128-byte (2M) sectored line size -- Private memory capability for half (1-Mbyte minimum) or all of the L3 SRAM space -- Supports MSUG2 dual data rate (DDR) synchronous Burst SRAMs, PB2 pipelined synchronous Burst SRAMs, and pipelined (register-register) late write synchronous Burst SRAMs -- Supports parity on cache and tags -- Configurable core-to-L3 frequency divisors -- 64-bit external L3 data bus sustains 64 bits per L3 clock cycle * Separate memory management units (MMUs) for instructions and data -- 52-bit virtual address; 32- or 36-bit physical address -- Address translation for 4-Kbyte pages, variable-sized blocks, and 256-Mbyte segments -- Memory programmable as write-back/write-through, caching-inhibited/caching-allowed, and memory coherency enforced/memory coherency not enforced on a page or block basis -- Separate IBATs and DBATs (eight each) also defined as SPRs -- Separate instruction and data translation lookaside buffers (TLBs) - Both TLBs are 128-entry, two-way set-associative, and use LRU replacement algorithm - TLBs are hardware- or software-reloadable (that is, on a TLB miss a page table search is performed in hardware or by system software) * Efficient data flow -- Although the VR/LSU interface is 128 bits, the L1/L2/L3 bus interface allows up to 256 bits -- The L1 data cache is fully pipelined to provide 128 bits/cycle to or from the VRs -- L2 cache is fully pipelined to provide 256 bits per processor clock cycle to the L1 cache -- As many as eight outstanding, out-of-order, cache misses are allowed between the L1 data cache and L2/L3 bus -- As many as 16 out-of-order transactions can be present on the MPX bus -- Store merging for multiple store misses to the same line. Only coherency action taken (address-only) for store misses merged to all 32 bytes of a cache block (no data tenure needed). -- Three-entry finished store queue and five-entry completed store queue between the LSU and the L1 data cache -- Separate additional queues for efficient buffering of outbound data (such as castouts and write through stores) from the L1 data cache and L2 cache * Multiprocessing support features include the following: -- Hardware-enforced, MESI cache coherency protocols for data cache -- Load/store with reservation instruction pair for atomic memory references, semaphores, and other multiprocessor operations 6 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Comparison with the MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441 * Power and thermal management -- 1.3-V processor core -- The following three power-saving modes are available to the system: - Nap--Instruction fetching is halted. Only those clocks for the time base, decrementer, and JTAG logic remain running. The part goes into the doze state to snoop memory operations on the bus and then back to nap using a QREQ/QACK processor-system handshake protocol. - Sleep--Power consumption is further reduced by disabling bus snooping, leaving only the PLL in a locked and running state. All internal functional units are disabled. - Deep sleep--When the part is in the sleep state, the system can disable the PLL. The system can then disable the SYSCLK source for greater system power savings. Power-on reset procedures for restarting and relocking the PLL must be followed on exiting the deep sleep state. -- Thermal management facility provides software-controllable thermal management. Thermal management is performed through the use of three supervisor-level registers and an MPC7455-specific thermal management exception. -- Instruction cache throttling provides control of instruction fetching to limit power consumption * * * Performance monitor can be used to help debug system designs and improve software efficiency In-system testability and debugging features through JTAG boundary-scan capability Testability -- LSSD scan design -- IEEE 1149.1 JTAG interface -- Array built-in self test (ABIST)--factory test only * Reliability and serviceability -- Parity checking on system bus and L3 cache bus -- Parity checking on the L2 and L3 cache tag arrays 1.3 Comparison with the MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441 Table 1 compares the key features of the MPC7455 with the key features of the earlier MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441. To achieve a higher frequency, the number of logic levels per cycle is reduced. Also, to achieve this higher frequency, the pipeline of the MPC7455 is extended (compared to the MPC7400), while maintaining the same level of performance as measured by the number of instructions executed per cycle (IPC). MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 7 Comparison with the MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441 Table 1. Microarchitecture Comparison Microarchitectural Specs MPC7455/MPC7445 MPC7450/MPC7451/ MPC7441 MPC7400/MPC7410 Basic Pipeline Functions Logic inversions per cycle Pipeline stages up to execute Total pipeline stages (minimum) Pipeline maximum instruction throughput 18 5 7 3 + Branch Pipeline Resources Instruction buffer size Completion buffer size Renames (integer, float, vector) 12 16 16, 16, 16 12 16 16, 16, 16 6 8 6, 6, 6 18 5 7 3 + Branch 28 3 4 2 + Branch Maximum Execution Throughput SFX Vector Scalar floating-point 3 2 (Any 2 of 4 Units) 1 3 2 (Any 2 of 4 Units) 1 2 2 (Permute/Fixed) 1 Out-of-Order Window Size in Execution Queues SFX integer units Vector units Scalar floating-point unit 1 Entry x 3 Queues In Order, 4 Queues In Order Branch Processing Resources Prediction structures BTIC size, associativity BHT size Link stack depth Unresolved branches supported Branch taken penalty (BTIC hit) Minimum misprediction penalty BTIC, BHT, Link Stack 128-Entry, 4-Way 2K-Entry 8 3 1 6 BTIC, BHT, Link Stack 128-Entry, 4-Way 2K-Entry 8 3 1 6 BTIC, BHT 64-Entry, 4-Way 512-Entry None 2 0 4 1 Entry x 3 Queues In Order, 4 Queues In Order 1 Entry x 2 Queues In Order, 2 Queues In Order Execution Unit Timings (Latency-Throughput) Aligned load (integer, float, vector) Misaligned load (integer, float, vector) L1 miss, L2 hit latency SFX (aDd Sub, Shift, Rot, Cmp, logicals) Integer multiply (32 x 8, 32 x 16, 32 x 32) Scalar float VSFX (vector simple) 3-1, 4-1, 3-1 4-2, 5-2, 4-2 9 Data/13 Instruction 1-1 3-1, 3-1, 4-2 5-1 1-1 3-1, 4-1, 3-1 4-2, 5-2, 4-2 9 Data/13 Instruction 1-1 3-1, 3-1, 4-2 5-1 1-1 2-1, 2-1, 2-1 3-2, 3-2, 3-2 9 (11) 1 1-1 2-1, 3-2, 5-4 3-1 1-1 8 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Comparison with the MPC7400, MPC7410, MPC7450, MPC7451, and MPC7441 Table 1. Microarchitecture Comparison (continued) Microarchitectural Specs VCFX (vector complex) VFPU (vector float) VPER (vector permute) MPC7455/MPC7445 4-1 4-1 2-1 MMUs TLBs (instruction and data) Tablewalk mechanism Instruction BATs/data BATs 128-Entry, 2-Way Hardware + Software 8/8 L1 I Cache/D Cache Features Size Associativity Locking granularity Parity on I cache Parity on D cache Number of D cache misses (load/store) Data stream touch engines 32K/32K 8-Way Way Word Byte 5/1 4 Streams On-Chip Cache Features Cache level Size/associativity Access width Number of 32-byte sectors/line Parity L2 256-Kbyte/8-Way 256 Bits 2 Byte Off-Chip Cache Support 2 Cache level On-chip tag logical size Associativity Number of 32-byte sectors/line Off-chip data SRAM support Data path width Direct mapped SRAM sizes Parity L3 1MB, 2MB 8-Way 2, 4 L3 1MB, 2MB 8-Way 2, 4 L2 0.5MB, 1MB, 2MB 2-Way 1, 2, 4 LW, PB2, PB3 64 0.5 Mbyte, 1 Mbyte, 2 Mbytes 3 Byte L2 256-Kbyte/8-Way 256 Bits 2 Byte L2 tags and controller only (see off-chip cache support below) 32K/32K 8-Way Way Word Byte 5/1 4 Streams 32K/32K 8-Way Full Cache None None 8 (Any Combination) 4 Streams 128-Entry, 2-Way Hardware + Software 4/4 128-Entry, 2-Way Hardware 4/4 MPC7450/MPC7451/ MPC7441 4-1 4-1 2-1 MPC7400/MPC7410 3-1 4-1 1-1 MSUG2 DDR, LW, PB2 MSUG2 DDR, LW, PB2 64 1 Mbyte, 2 Mbytes Byte 64 1 Mbyte, 2 Mbytes Byte Notes: 1. Numbers in parentheses are for 2:1 SRAM. 2. Not implemented on MPC7445 or MPC7441. 3. Private memory feature not implemented on MPC7400. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 9 General Parameters 1.4 General Parameters Technology Die size Transistor count Logic design Packages Core power supply I/O power supply 0.18 m CMOS, six-layer metal 8.69 mm x 12.17 mm (106 mm2) 33 million Fully-static MPC7445: Surface mount 360 ceramic ball grid array (CBGA) MPC7455: Surface mount 483 ceramic ball grid array (CBGA) 1.3 V 50 mV DC nominal 1.8 V 5% DC, or 2.5 V 5% DC, or 1.5 V 5% DC (L3 interface only) The following list provides a summary of the general parameters of the MPC7455: 1.5 1.5.1 Electrical and Thermal Characteristics DC Electrical Characteristics This section provides the AC and DC electrical specifications and thermal characteristics for the MPC7455. The tables in this section describe the MPC7455 DC electrical characteristics. Table 2 provides the absolute maximum ratings. Table 2. Absolute Maximum Ratings 1 Characteristic Core supply voltage PLL supply voltage Processor bus supply voltage BVSEL = 0 BVSEL = HRESET or OVDD L3 bus supply voltage L3VSEL = HRESET L3VSEL = 0 L3VSEL = HRESET or GVDD Input voltage Processor bus L3 bus JTAG signals Input voltage Processor bus JTAG signals Symbol VDD AVDD OVDD OVDD GVDD GVDD GVDD Vin Vin Vin Vin Vin Maximum Value -0.3 to 1.95 -0.3 to 1.95 -0.3 to 1.95 -0.3 to 2.7 -0.3 to 1.65 -0.3 to 1.95 -0.3 to 2.7 -0.3 to OVDD + 0.3 -0.3 to GVDD + 0.3 -0.3 to OVDD + 0.3 -0.3 to OVDD + 0.3 -0.3 to OVDD + 0.3 Unit V V V V V V V V V V V V 2, 5 Notes 4 4 3, 6 3, 7 3, 8 3, 9 3, 10 2, 5 2, 5 10 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Table 2. Absolute Maximum Ratings 1 (continued) Characteristic Storage temperature range Symbol Tstg Maximum Value -55 to 150 Unit C Notes Notes: 1. Functional and tested operating conditions are given in Table 4. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: Vin must not exceed OVDD or GVDD by more than 0.3 V at any time including during power-on reset. 3. Caution: OVDD/GVDD must not exceed VDD/AVDD by more than 2.0 V during normal operation; this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. Caution: VDD/AVDD must not exceed OVDD/GVDD by more than 1.0 V during normal operation; this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 5. Vin may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2. 6. BVSEL must be set to 0, such that the bus is in 1.8 V mode. 7. BVSEL must be set to HRESET or 1, such that the bus is in 2.5 V mode. 8. L3VSEL must be set to HRESET (inverse of HRESET), such that the bus is in 1.5 V mode. 9. L3VSEL must be set to 0, such that the bus is in 1.8 V mode. 10. L3VSEL must be set to HRESET or 1, such that the bus is in 2.5 V mode. Figure 2 shows the undershoot and overshoot voltage on the MPC7455. OVDD/GVDD + 20% OVDD/GVDD + 5% OVDD/GVDD VIH VIL GND GND - 0.3 V GND - 0.7 V Not to Exceed 10% of tSYSCLK Figure 2. Overshoot/Undershoot Voltage The MPC7455 provides several I/O voltages to support both compatibility with existing systems and migration to future systems. The MPC7455 core voltage must always be provided at nominal 1.3 V (see Table 4 for actual recommended core voltage). Voltage to the L3 I/Os and processor interface I/Os are provided through separate sets of supply pins and may be provided at the voltages shown in Table 3. The input voltage threshold for each bus is selected by sampling the state of the voltage select pins at the negation of the signal HRESET. The output voltage will swing from GND to the maximum voltage applied to the OVDD or GVDD power pins. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 11 Electrical and Thermal Characteristics Table 3. Input Threshold Voltage Setting BVSEL Signal 0 HRESET HRESET 1 Processor Bus Input Threshold is Relative to: 1.8 V Not Available 2.5 V 2.5 V L3VSEL Signal 5 0 HRESET HRESET 1 L3 Bus Input Threshold is Relative to: 1.8 V 1.5 V 2.5 V 2.5 V Notes 1, 4 1, 3 1, 2 1 Notes: 1. Caution: The input threshold selection must agree with the OVDD/GVDD voltages supplied. See notes in Table 2. 2. To select the 2.5-V threshold option for the processor bus, BVSEL should be tied to HRESET so that the two signals change state together. Similarly, to select 2.5 V for the L3 bus, tie L3VSEL to HRESET. This is the preferred method for selecting this mode of operation. 3. Applicable to L3 bus interface only. HRESET is the inverse of HRESET. 4. If used, pulldown resistors should be less than 250 . 5. Not implemented on MPC7445. Table 4 provides the recommended operating conditions for the MPC7455. Table 4. Recommended Operating Conditions 1 Recommended Value Characteristic Symbol Min Core supply voltage PLL supply voltage Processor bus supply voltage BVSEL = 0 BVSEL = HRESET or OVDD L3 bus supply voltage L3VSEL = 0 L3VSEL = HRESET or GVDD L3VSEL = HRESET Input voltage Processor bus L3 bus JTAG signals Input voltage Processor bus JTAG signals Die-junction temperature VDD AVDD OVDD OVDD GVDD GVDD GVDD Vin Vin Vin Vin Vin Tj Max V V V V V V V V V V V V C 2 Unit Notes 1.3 V 50 mV 1.3 V 50 mV 1.8 V 5% 2.5 V 5% 1.8 V 5% 2.5 V 5% 1.5 V 5% GND GND GND GND GND 0 OVDD GVDD OVDD OVDD OVDD 105 Notes: 1. These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. 2. This voltage is the input to the filter discussed in Section 1.9.2, "PLL Power Supply Filtering," and not necessarily the voltage at the AVDD pin which may be reduced from VDD by the filter. 12 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Table 5 provides the package thermal characteristics for the MPC7455. Table 5. Package Thermal Characteristics 6 Value Characteristic Symbol MPC7445 Junction-to-ambient thermal resistance, natural convection Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board Junction-to-ambient thermal resistance, 200 ft/min airflow, single-layer (1s) board Junction-to-ambient thermal resistance, 200 ft/min airflow, four-layer (2s2p) board Junction-to-board thermal resistance Junction-to-case thermal resistance RJA RJMA RJMA RJMA RJB RJC 22 14 16 11 6 <0.1 MPC7455 20 14 15 11 6 <0.1 C/W C/W C/W C/W C/W C/W 1, 2 1, 3 1, 3 1, 3 4 5 Unit Notes Notes: 1. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, airflow, power dissipation of other components on the board, and board thermal resistance. 2. Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal. 3. Per JEDEC JESD51-6 with the board horizontal. 4. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1) with the calculated case temperature. The actual value of RJC for the part is less than 0.1C/W. 6. Refer to Section 1.9.8, "Thermal Management Information," for more details about thermal management. Table 6 provides the DC electrical characteristics for the MPC7455. Table 6. DC Electrical Specifications At recommended operating conditions. See Table 4. Characteristic Nominal Bus Voltage 1 1.5 1.8 2.5 Symbol Min GVDD x 0.65 OVDD/GVDD x 0.65 1.7 OVDD/GVDD x 0.65 1.7 -0.3 -0.3 -0.3 Max Unit Notes Input high voltage (all inputs except SYSCLK) VIH VIH VIH VIH VIH VIL VIL VIL GVDD + 0.3 OVDD/GVDD + 0.3 OVDD/GVDD + 0.3 OVDD + 0.3 OVDD + 0.3 GVDD x 0.35 OVDD/GVDD x 0.35 0.7 V V V V V V V V 6 Input high voltage (all inputs except SYSCLK) Input low voltage (all inputs except SYSCLK) 1.8 2.5 1.5 1.8 2.5 6 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 13 Electrical and Thermal Characteristics Table 6. DC Electrical Specifications (continued) At recommended operating conditions. See Table 4. Characteristic Nominal Bus Voltage 1 1.8 2.5 -- -- -- -- 1.5 1.8 2.5 Symbol Min Max OVDD x 0.35 0.7 OVDD + 0.3 0.4 30 30 -- -- -- -- -- 0.45 0.45 0.7 0.45 0.7 9.5 8.0 8.0 Unit Notes Input low voltage (all inputs except SYSCLK) SYSCLK input high voltage SYSCLK input low voltage Input leakage current, Vin = GVDD/OVDD + 0.3 V High impedance (off-state) leakage current, Vin = GVDD/OVDD + 0.3 V Output high voltage, IOH = -5 mA VIL VIL CVIH CVIL Iin ITSI VOH VOH VOH VOH VOH VOL VOL VOL VOL VOL Cin -0.3 -0.3 1.4 -0.3 -- -- OVDD/GVDD - 0.45 OVDD/GVDD - 0.45 1.7 OVDD/GVDD - 0.45 1.7 -- -- -- -- -- -- -- V V V V A A V V V V V V V V V V pF pF pF 4 4 4 6 2, 3 2, 3, 5 6 Output high voltage, IOH = -5 mA 1.8 2.5 Output low voltage, IOL = 5 mA 1.5 1.8 2.5 Output low voltage, IOL = 5 mA 1.8 2.5 Capacitance, Vin = 0 V, f = 1 MHz Capacitance, Vin = 0 V, f = 1 MHz L3 interface All other inputs All inputs -- -- Cin -- Notes: 1. Nominal voltages; see Table 4 for recommended operating conditions. 2. For processor bus signals, the reference is OVDD while GVDD is the reference for the L3 bus signals. 3. Excludes test signals and IEEE 1149.1 boundary scan (JTAG) signals. 4. Capacitance is periodically sampled rather than 100% tested. 5. The leakage is measured for nominal OVDD/GVDD and VDD, or both OVDD/GVDD and VDD must vary in the same direction (for example, both OVDD and VDD vary by either +5% or -5%). 6. Applicable to L3 bus interface only. 14 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Table 7 provides the power consumption for the MPC7455. Table 7. Power Consumption for MPC7455 Processor (CPU) Frequency Unit 733 MHz 867 MHz 933 MHz 1 GHz Notes Full-Power Mode Typical Maximum 11.5 17.0 12.9 19.0 13.6 20.0 15.0 22.0 W W 1, 3 1, 2 Doze Mode Typical -- -- Nap Mode Typical 8.0 8.0 8.0 8.0 W 1, 3 -- -- W 1, 3, 4 Sleep Mode Typical 7.6 7.6 7.6 7.6 W 1, 3 Deep Sleep Mode (PLL Disabled) Typical 7.3 7.3 7.3 7.3 W 1, 3 Notes: 1. These values apply for all valid processor bus and L3 bus ratios. The values do not include I/O supply power (OVDD and GVDD) or PLL supply power (AVDD). OVDD and GVDD power is system dependent, but is typically <5% of VDD power. Worst case power consumption for AVDD < 3 mW. 2. Maximum power is measured at nominal VDD (see Table 4) while running an entirely cache-resident, contrived sequence of instructions which keep the execution units, with or without AltiVec, maximally busy. 3. Typical power is an average value measured at the nominal recommended VDD (see Table 4) and 65C in a system while running a typical code sequence. 4. Doze mode is not a user-definable state; it is an intermediate state between full-power and either nap or sleep mode. As a result, power consumption for this mode is not tested. 1.5.2 AC Electrical Characteristics This section provides the AC electrical characteristics for the MPC7455. After fabrication, functional parts are sorted by maximum processor core frequency as shown in Section 1.5.2.1, "Clock AC Specifications," and tested for conformance to the AC specifications for that frequency. The processor core frequency is determined by the bus (SYSCLK) frequency and the settings of the PLL_CFG[0:4] signals. Parts are sold by maximum processor core frequency; see Section 1.11, "Ordering Information." 1.5.2.1 Clock AC Specifications Table 8 provides the clock AC timing specifications as defined in Figure 3. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 15 Electrical and Thermal Characteristics Table 8. Clock AC Timing Specifications At recommended operating conditions. See Table 4. Maximum Processor Core Frequency Characteristic Symbol 733 MHz Min Processor frequency VCO frequency SYSCLK frequency SYSCLK cycle time SYSCLK rise and fall time SYSCLK duty cycle measured at OVDD/2 SYSCLK jitter Internal PLL relock time fcore fVCO fSYSCLK tSYSCLK tKR, tKF tKHKL/ tSYSCLK 500 1000 33 7.5 -- 40 -- -- Max 733 1466 133 30 1.0 60 150 100 867 MHz Min 500 1000 33 7.5 -- 40 -- -- Max 867 1734 133 30 1.0 60 150 100 933 MHz Min 500 1000 33 7.5 -- 40 -- -- Max 933 1866 133 30 1.0 60 150 100 1 GHz Min 500 1000 33 7.5 -- 40 -- -- Max 1000 2000 133 30 1.0 60 150 100 MHz MHz MHz ns ns % ps s 2 3 4, 6 5 1 1 1 Unit Notes Notes: 1. Caution: The SYSCLK frequency and PLL_CFG[0:4] settings must be chosen such that the resulting SYSCLK (bus) frequency, CPU (core) frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum operating frequencies. Refer to the PLL_CFG[0:4] signal description in Section 1.9.1, "PLL Configuration," for valid PLL_CFG[0:4] settings. 2. Rise and fall times for the SYSCLK input measured from 0.4 to 1.4 V. 3. Timing is guaranteed by design and characterization. 4. This represents total input jitter--short term and long term combined--and is guaranteed by design. 5. Relock timing is guaranteed by design and characterization. PLL-relock time is the maximum amount of time required for PLL lock after a stable VDD and SYSCLK are reached during the power-on reset sequence. This specification also applies when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must be held asserted for a minimum of 255 bus clocks after the PLL-relock time during the power-on reset sequence. 6. The SYSCLK driver's closed loop jitter bandwidth should be <500 kHz at -20 dB. The bandwidth must be set low to allow cascade connected PLL-based devices to track SYSCLK drivers with the specified jitter. Figure 3 provides the SYSCLK input timing diagram. SYSCLK VM tKHKL tSYSCLK VM = Midpoint Voltage (OVDD/2) VM VM CVIH CVIL tKR tKF Figure 3. SYSCLK Input Timing Diagram 1.5.2.2 Processor Bus AC Specifications Table 9 provides the processor bus AC timing specifications for the MPC7455 as defined in Figure 4 and Figure 5. Timing specifications for the L3 bus are provided in Section 1.5.2.3, "L3 Clock AC Specifications." 16 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Table 9. Processor Bus AC Timing Specifications 1 At recommended operating conditions. See Table 4. All Speed Grades Parameter Symbol 2 Min Mode select input setup to HRESET HRESET to mode select input hold Input setup times: A[0:35], AP[0:4], GBL, TBST, TSIZ[0:2], TT[0:3], D[0:63], DP[0:7] AACK, ARTRY, BG, CKSTP_IN, DBG, DTI[0:3], QACK, TA, TBEN, TEA, TS, EXT_QUAL, PMON_IN, SHD[0:1] Input hold times: A[0:35], AP[0:4], GBL, TBST, TSIZ[0:2], TT[0:3], D[0:63], DP[0:7] AACK, ARTRY, BG, CKSTP_IN, DBG, DTI[0:3], QACK, TA,TBEN, TEA, TS,EXT_QUAL, PMON_IN, SHD[0:1] Output valid times: A[0:35], AP[0:4], GBL, TBST, TSIZ[0:2], TT[0:3], WT, CI TS D[0:63], DP[0:7] ARTRY/SHD0/SHD1 BR, CKSTP_OUT, DRDY, HIT, PMON_OUT, QREQ] Output hold times: A[0:35], AP[0:4], GBL, TBST, TSIZ[0:2], TT[0:3], WT, CI TS D[0:63], DP[0:7] ARTRY/SHD0/SHD1 BR, CKSTP_OUT, DRDY, HIT, PMON_OUT, QREQ SYSCLK to output enable SYSCLK to output high impedance (all except TS, ARTRY, SHD0, SHD1) SYSCLK to TS high impedance after precharge Maximum delay to ARTRY/SHD0/SHD1 precharge tMVRH tMXRH tAVKH tIVKH 8 0 2.0 2.0 Max -- -- -- -- tSYSCLK ns ns 3, 4, 5, 6 3, 6 Unit Notes ns tAXKH tIXKH 0 0 -- -- ns tKHAV tKHTSV tKHDV tKHARV tKHOV tKHAX tKHTSX tKHDX tKHARX tKHOX tKHOE tKHOZ tKHTSPZ tKHARP -- -- -- -- -- 0.5 0.5 0.5 0.5 0.5 0.5 -- -- -- 2.5 2.5 2.5 2.5 2.5 ns -- -- -- -- -- -- 3.5 1 1 ns ns tSYSCLK tSYSCLK 5, 7, 10 5, 8, 9, 10 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 17 Electrical and Thermal Characteristics Table 9. Processor Bus AC Timing Specifications 1 (continued) At recommended operating conditions. See Table 4. All Speed Grades Parameter Symbol 2 Min SYSCLK to ARTRY/SHD0/SHD1 high impedance after precharge tKHARPZ -- Max 2 tSYSCLK 5, 8, 9, 10 Unit Notes Notes: 1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the signal in question. All output timings assume a purely resistive 50- load (see Figure 4). Input and output timings are measured at the pin; time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. The symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs and t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid state (V) relative to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV symbolizes the time from SYSCLK(K) going high (H) until outputs (O) are valid (V) or output valid time. Input hold time can be read as the time that the input signal (I) went invalid (X) with respect to the rising clock edge (KH) (note the position of the reference and its state for inputs) and output hold time can be read as the time from the rising edge (KH) until the output went invalid (OX). 3. The setup and hold time is with respect to the rising edge of HRESET (see Figure 5). 4. This specification is for configuration mode select only. 5. tSYSCLK is the period of the external clock (SYSCLK) in ns. The numbers given in the table must be multiplied by the period of SYSCLK to compute the actual time duration (in ns) of the parameter in question. 6. Mode select signals are: BVSEL, L3VSEL, PLL_CFG[0:4], BMODE[0:1]. 7. According to the bus protocol, TS is driven only by the currently active bus master. It is asserted low then precharged high before returning to high impedance as shown in Figure 6. The nominal precharge width for TS is 0.5 x tSYSCLK, that is, less than the minimum tSYSCLK period, to ensure that another master asserting TS on the following clock will not contend with the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for precharge.The high-impedance behavior is guaranteed by design. 8. According to the bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following AACK. Bus contention is not an issue because any master asserting ARTRY will be driving it low. Any master asserting it low in the first clock following AACK will then go to high impedance for one clock before precharging it high during the second cycle after the assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK; that is, it should be high impedance as shown in Figure 6 before the first opportunity for another master to assert ARTRY. Output valid and output hold timing is tested for the signal asserted. The high-impedance behavior is guaranteed by design. 9. According to the MPX bus protocol, SHD0 and SHD1 can be driven by multiple bus masters beginning the cycle of TS. Timing is the same as ARTRY, that is, the signal is high impedance for a fraction of a cycle, then negated for up to an entire cycle (crossing a bus cycle boundary) before being three-stated again. The nominal precharge width for SHD0 and SHD1 is 1.0 tSYSCLK. The edges of the precharge vary depending on the programmed ratio of core to bus (PLL configurations). 10. Guaranteed by design and not tested. Figure 4 provides the AC test load for the MPC7455. Output Z0 = 50 OVDD/2 RL = 50 Figure 4. AC Test Load 18 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Figure 5 provides the mode select input timing diagram for the MPC7455. HRESET tMVRH tMXRH Mode Signals VM = Midpoint Voltage (OVDD/2) VM Figure 5. Mode Input Timing Diagram Figure 6 provides the input/output timing diagram for the MPC7455. SYSCLK VM tAVKH tIVKH All Inputs tKHAV tKHDV All Outputs (Except TS, ARTRY, SHD0, SHD1) tKHOE VM tAXKH tIXKH VM tKHAX tKHDX tKHOX tKHOV All Outputs (Except TS, ARTRY, SHD0, SHD1) tKHOZ tKHTSPZ tKHTSV tKHTSX tKHTSV TS tKHARPZ tKHARV ARTRY, SHD0, SHD1 tKHARP tKHARX VM = Midpoint Voltage (OVDD/2) Figure 6. Input/Output Timing Diagram MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 19 Electrical and Thermal Characteristics 1.5.2.3 L3 Clock AC Specifications The L3_CLK frequency is programmed by the L3 configuration register (L3CR[6:8]) core-to-L3 divisor ratio. See Table 18 for example core and L3 frequencies at various divisors. Table 10 provides the potential range of L3_CLK output AC timing specifications as defined in Figure 7. The maximum L3_CLK frequency is the core frequency divided by two. Given the high core frequencies available in the MPC7455, however, most SRAM designs will be not be able to operate in this mode using current technology and, as a result, will select a greater core-to-L3 divisor to provide a longer L3_CLK period for read and write access to the L3 SRAMs. Therefore, the maximum L3_CLK frequency shown in Table 10 is considered to be the practical maximum in a typical system. The maximum L3_CLK frequency for any application of the MPC7455 will be a function of the AC timings of the MPC7455, the AC timings for the SRAM, bus loading, and printed-circuit board trace length, and may be greater or less than the value given in Table 10. Motorola is similarly limited by system constraints and cannot perform tests of the L3 interface on a socketed part on a functional tester at the maximum frequencies of Table 10. Therefore, functional operation and AC timing information are tested at core-to-L3 divisors which result in L3 frequencies at 200 MHz or less. Table 10. L3_CLK Output AC Timing Specifications At recommended operating conditions. See Table 4. All Speed Grades Parameter Symbol Min L3 clock frequency L3 clock cycle time L3 clock duty cycle L3 clock output-to-output skew (L1_CLK0 to L1_CLK1) L3 clock output-to-output skew (L1_CLK[0:1] to L1_ECHO_CLK[2:3]) L3 clock jitter fL3_CLK tL3_CLK tCHCL/tL3_CLK tL3CSKW1 tL3CSKW2 -- -- -- 75 3.75 50 200 100 50 Max 266 13.3 MHz ns % ps ps ps 2 3 4 5 1 Unit Notes Notes: 1. The maximum L3 clock frequency will be system dependent. See Section 1.5.2.3, "L3 Clock AC Specifications," for an explanation that this maximum frequency is not functionally tested at speed by Motorola. 2. The nominal duty cycle of the L3 output clocks is 50% measured at midpoint voltage. 3. Maximum possible skew between L3_CLK0 and L3_CLK1. This parameter is critical to the address and control signals which are common to both SRAM chips in the L3. 4. Maximum possible skew between L3_CLK0 and L3_ECHO_CLK1 or between L3_CLK1 and L3_ECHO_CLK3 for PB2 or late write SRAM. This parameter is critical to the write data signals which are separately latched onto each SRAM part by these pairs of signals. 5. Guaranteed by design and not tested. The input jitter on SYSCLK affects L3 output clocks and the L3 address/data/control signals equally and, therefore, is already comprehended in the AC timing and does not have to be considered in the L3 timing analysis. The clock-to-clock jitter shown here is uncertainty in the internal clock period caused by supply voltage noise or thermal effects. This must be accounted for, along with clock skew, in any L3 timing analysis. 20 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics The L3_CLK timing diagram is shown in Figure 7. tL3_CLK tCHCL L3_CLK0 VM VM VM tL3CR tL3CF L3_CLK1 VM VM VM tL3CSKW1 VM For PB2 or Late Write: L3_ECHO_CLK1 VM VM VM tL3CSKW2 VM L3_ECHO_CLK3 VM VM VM tL3CSKW2 VM Figure 7. L3_CLK_OUT Output Timing Diagram 1.5.2.4 L3 Bus AC Specifications The MPC7455 L3 interface supports three different types of SRAM: source-synchronous, double data rate (DDR) MSUG2 SRAM, late write SRAMs, and pipeline burst (PB2) SRAMs. Each requires a different protocol on the L3 interface and a different routing of the L3 clock signals. The type of SRAM is programmed in L3CR[22:23] and the MPC7455 then follows the appropriate protocol for that type. The designer must connect and route the L3 signals appropriately for each type of SRAM. Following are some observations about the chip-to-SRAM interface. * The routing for the point-to-point signals (L3_CLK[0:1], L3DATA[0:63], L3DP[0:7], and L3_ECHO_CLK[0:3]) to a particular SRAM should be delay matched. If necessary, the length of traces can be altered in order to intentionally skew the timing and provide additional setup or hold time margin. For a 1-Mbyte L3, use address bits 16:0 (bit 0 is LSB) No pull-up resistors are required for the L3 interface For high speed operations, L3 interface address and control signals should be a `T' with minimal stubs to the two loads; data and clock signals should be point-to-point to their single load. Figure 8 shows the AC test load for the L3 interface. Output Z0 = 50 GVDD/2 * * * RL = 50 Figure 8. AC Test Load for the L3 Interface In general, if routing is short, delay-matched, and designed for incident wave reception and minimal reflection, there is a high probability that the AC timing of the MPC7455 L3 interface will meet the maximum frequency operation of appropriately chosen SRAMs. This is despite the pessimistic, guard-banded AC specifications (see Table 12, Table 13, and Table 14), the limitations of functional testers MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 21 Electrical and Thermal Characteristics described in Section 1.5.2.3, "L3 Clock AC Specifications," and the uncertainty of clocks and signals which inevitably make worst-case critical path timing analysis pessimistic. More specifically, certain signals within groups should be delay-matched with others in the same group while intergroup routing is less critical. Only the address and control signals are common to both SRAMs and additional timing margin is available for these signals. The double-clocked data signals are grouped with individual clocks as shown in Figure 9 or Figure 11, depending on the type of SRAM. For example, for the MSUG2 DDR SRAM (see Figure 9); L3DATA[0:31], L3DP[0:3], and L3_CLK[0] form a closely coupled group of outputs from the MPC7455; while L3DATA[0:15], L3DP[0:1], and L3_ECHO_CLK[0] form a closely coupled group of inputs. The MPC7450 RISC Microprocessor Family User's Manual refers to logical settings called `sample points' used in the synchronization of reads from the receive FIFO. The computation of the correct value for this setting is system-dependent and is described in the MPC7450 RISC Microprocessor Family User's Manual. Three specifications are used in this calculation and are given in Table 11. It is essential that all three specifications are included in the calculations to determine the sample points, as incorrect settings can result in errors and unpredictable behavior. For more information, see the MPC7450 RISC Microprocessor Family User's Manual. Table 11. Sample Points Calculation Parameters Parameter Delay from processor clock to internal_L3_CLK Delay from internal_L3_CLK to L3_CLKn output pins Delay from L3_ECHO_CLKn to receive latch Symbol tAC tCO tECI Max 3/4 3 3 Unit tL3_CLK ns ns Notes 1 2 3 Notes: 1. This specification describes a logical offset between the internal clock edge used to launch the L3 address and control signals (this clock edge is phase-aligned with the processor clock edge) and the internal clock edge used to launch the L3_CLKn signals. With proper board routing, this offset ensures that the L3_CLKn edge will arrive at the SRAM within a valid address window and provide adequate setup and hold time. This offset is reflected in the L3 bus interface AC timing specifications, but must also be separately accounted for in the calculation of sample points and, thus, is specified here. 2. This specification is the delay from a rising or falling edge on the internal_L3_CLK signal to the corresponding rising or falling edge at the L3CLKn pins. 3. This specification is the delay from a rising or falling edge of L3_ECHO_CLKn to data valid and ready to be sampled from the FIFO. 1.5.2.4.1 L3 Bus AC Specifications for DDR MSUG2 SRAMs When using DDR MSUG2 SRAMs at the L3 interface, the parts should be connected as shown in Figure 9. Outputs from the MPC7455 are actually launched on the edges of an internal clock phase-aligned to SYSCLK (adjusted for core and L3 frequency divisors). L3_CLK0 and L3_CLK1 are this internal clock output with 90 phase delay, so outputs are shown synchronous to L3_CLK0 and L3_CLK1. Output valid times are typically negative when referenced to L3_CLKn because the data is launched one-quarter period before L3_CLKn to provide adequate setup time at the SRAM after the delay-matched address, control, data, and L3_CLKn signals have propagated across the printed-wiring board. Inputs to the MPC7455 are source-synchronous with the CQ clock generated by the DDR MSUG2 SRAMs. These CQ clocks are received on the L3_ECHO_CLKn inputs of the MPC7455. An internal circuit delays the incoming L3_ECHO_CLKn signal such that it is positioned within the valid data window at the internal receiving latches. This delayed clock is used to capture the data into these latches which comprise the 22 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA receive FIFO. This clock is asynchronous to all other processor clocks. This latched data is subsequently read out of the FIFO synchronously to the processor clock. The time between writing and reading the data is set by the using the sample point settings defined in the L3CR register. Electrical and Thermal Characteristics MOTOROLA Table 12. L3 Bus Interface AC Timing Specifications for MSUG2 All Speed Grades 8 Symbol Min tL3CR, tL3CF tL3DVEH, tL3DVEL tL3DXEH, tL3DXEL tL3_CLK/4 + 0.30 -- -- tL3_CLK/4 - 0.40 tL3_CLK/4 - 0.20 -- tL3_CLK/2 -- tL3_CLK/4 - 0.04 -- -- tL3_CLK/4 - 0.24 -- -- tL3_CLK/2 tL3_CLK/4 + 0.80 -- tL3_CLK/4 + 0.96 (- tL3_CLK/4) + 0.4 0 -- (- tL3_CLK/4) + 0.56 -- -- tL3_CLK/4 - 0.08 tL3_CLK/4 + 0.12 -- -- tL3_CLK/4 + 0.30 -- tL3CHDV, tL3CLDV tL3CHOV tL3CHDX, tL3CLDX, tL3CHOX tL3CLDZ tL3_CLK/4 + 0.30 - 0.1 -- - 0.1 -- - 0.1 -- -- (- tL3_CLK/4) + 0.72 tL3_CLK/4 + 1.12 -- -- tL3_CLK/2 -- 1.0 -- 1.0 -- 1.0 Max Min Max Min Max Min -- - 0.1 tL3_CLK/4 + 0.30 -- -- tL3_CLK/4 + 0.08 tL3_CLK/4 + 0.28 -- L3OH0 = 0, L3OH1 = 0 L3OH0 = 0, L3OH1 =1 L3OH0 = 1, L3OH1 = 0 L3OH0 = 1, L3OH1 = 1 Max 1.0 -- -- (- tL3_CLK/4) + 0.98 tL3_CLK/4 + 1.28 -- -- tL3_CLK/2 ns ns ns ns ns ns ns ns 1 2, 3, 4 2, 4 5, 6, 7 5, 7 5, 6, 7 5, 7 Unit Table 12 provides the L3 bus interface AC timing specifications for the configuration as shown in Figure 9, assuming the timing relationships shown in Figure 10 and the loading shown in Figure 8. At recommended operating conditions. See Table 4. Parameter Notes L3_CLK rise and fall time Setup times: Data and parity Input hold times: Data and parity Valid times: Data and parity Valid times: All other outputs Output hold times: Data and parity MPC7455 RISC Microprocessor Hardware Specifications Output hold times: All other outputs L3_CLK to high impedance: Data and parity 23 Table 12. L3 Bus Interface AC Timing Specifications for MSUG2 (continued) All Speed Grades 8 Symbol Min tL3CHOZ -- tL3_CLK/4 + 2.0 -- tL3_CLK/4 + 2.0 tL3_CLK/4 + 2.0 -- tL3_CLK/4 + 2.0 Max Min Max Min Max Min Max -- ns L3OH0 = 0, L3OH1 = 0 L3OH0 = 0, L3OH1 =1 L3OH0 = 1, L3OH1 = 0 L3OH0 = 1, L3OH1 = 1 Unit Notes 24 At recommended operating conditions. See Table 4. Parameter Electrical and Thermal Characteristics L3_CLK to high impedance: All other outputs MPC7455 RISC Microprocessor Hardware Specifications Notes: 1. Rise and fall times for the L3_CLK output are measured from 20% to 80% of GVDD. 2. For DDR, all input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising or falling edge of the input L3_ECHO_CLKn (see Figure 10). Input timings are measured at the pins. 3. For DDR, the input data will typically follow the edge of L3_ECHO_CLKn as shown in Figure 10. For consistency with other input setup time specifications, this will be treated as negative input setup time. 4. tL3_CLK/4 is one-fourth the period of L3_CLKn. This parameter indicates that the MPC7455 can latch an input signal that is valid for only a short time before and a short time after the midpoint between the rising and falling (or falling and rising) edges of L3_ECHO_CLKn at any frequency. 5. All output specifications are measured from the midpoint voltage of the rising (or for DDR write data, also the falling) edge of L3_CLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50- load (see Figure 8). 6. For DDR, the output data will typically lead the edge of L3_CLKn as shown in Figure 10. For consistency with other output valid time specifications, this will be treated as negative output valid time. 7. tL3_CLK/4 is one-fourth the period of L3_CLKn. This parameter indicates that the specified output signal is actually launched by an internal clock delayed in phase by 90. Therefore, there is a frequency component to the output valid and output hold times such that the specified output signal will be valid for approximately one L3_CLK period starting three-fourths of a clock prior to the edge on which the SRAM will sample it and ending one-fourth of a clock period after the edge it will be sampled. 8. These configuration bits allow the AC timing of the L3 interface to be altered via software. L3OH0 = L2CR[12], L30H1 = L3CR[12]. Revisions of the MPC7455 not described by this document may implement these bits differently. See Section 1.11.1, "Part Numbers Fully Addressed by This Document," and Section 1.11.2, "Part Numbers Not Fully Addressed by This Document," for more information on which devices are addressed by this document. MOTOROLA Electrical and Thermal Characteristics Figure 9 shows the typical connection diagram for the MPC7455 interfaced to MSUG2 SRAMs such as the Motorola MCM64E836. MPC7455 L3ADDR[17:0] L3_CNTL[0] L3_CNTL[1] Denotes Receive (SRAM to MPC7455) Aligned Signals L3_ECHO_CLK[0] {L3DATA[0:15], L3DP[0:1]} L3_CLK[0] {L3DATA[16:31], L3DP[2:3]} L3_ECHO_CLK[1] Denotes Transmit (MPC7455 to SRAM) Aligned Signals L3ECHO_CLK[2] {L3_DATA[32:47], L3DP[4:5]} L3_CLK[1] {L3DATA[48:63], L3DP[6:7]} L3_ECHO_CLK[3] SRAM 0 SA[17:0] B1 B2 CQ D[0:17] CK D[18:35] CQ SRAM 1 SA[17:0] B3 B1 G B2 CQ D[0:17] CK D[18:35] CQ LBO CQ CQ CK B3 G GND GND GND NC NC GVDD/2 1 LBO CQ CQ CK GND GND GND NC NC GVDD/2 1 Note: 1. Or as recommended by SRAM manufacturer for single-ended clocking. Figure 9. Typical Source Synchronous 2-Mbyte L3 Cache DDR Interface MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 25 Electrical and Thermal Characteristics Figure 10 shows the L3 bus timing diagrams for the MPC7455 interfaced to MSUG2 SRAMs. Outputs L3_CLK[0,1] VM tL3CHOV VM tL3CHOZ tL3CHOX ADDR, L3CNTL tL3CLDV tL3CHDV L3DATA WRITE tL3CHDX tL3CLDX VM = Midpoint Voltage (GVDD/2) Note: tL3CHDV and tL3CLDV as drawn here will be negative numbers, that is, output valid time will be time before the clock edge. Inputs L3_ECHO_CLK[0,1,2,3] VM VM tL3DVEL tL3DVEH L3 Data and Data Parity Inputs tL3DXEH VM = Midpoint Voltage (GVDD/2) Note: tL3DVEH and tL3DVEL as drawn here will be negative numbers, that is, input setup time will be time after the clock edge. VM VM tL3DXEL VM tL3CLDZ VM VM VM Figure 10. L3 Bus Timing Diagrams for L3 Cache DDR SRAMs 1.5.2.4.2 L3 Bus AC Specifications for PB2 and Late Write SRAMs When using PB2 or late write SRAMs at the L3 interface, the parts should be connected as shown in Figure 11. These SRAMs are synchronous to the MPC7455; one L3_CLKn signal is output to each SRAM to latch address, control, and write data. Read data is launched by the SRAM synchronous to the delayed L3_CLKn signal it received. The MPC7455 needs a copy of that delayed clock which launched the SRAM read data to know when the returning data will be valid. Therefore, L3_ECHO_CLK1 and L3_ECHO_CLK3 must be routed halfway to the SRAMs and then returned to the MPC7455 inputs L3_ECHO_CLK0 and L3_ECHO_CLK2, respectively. Thus, L3_ECHO_CLK0 and L3_ECHO_CLK2 are phase-aligned with the input clock received at the SRAMs. The MPC7455 will latch the incoming data on the rising edge of L3_ECHO_CLK0 and L3_ECHO_CLK2. Table 13 provides the L3 bus interface AC timing specifications for the configuration shown in Figure 11, assuming the timing relationships of Figure 12 and the loading of Figure 8. 26 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Table 13. L3 Bus Interface AC Timing Specifications for PB2 and Late Write SRAMs All Speed Grades 6 Symbol Min tL3CR, tL3CF -- 1.5 -- -- -- tL3_CLK/4 - 0.40 tL3_CLK/4 - 0.40 -- 2.0 -- 2.0 -- tL3_CLK/4 - 0.24 -- -- tL3_CLK/4 - 0.24 -- tL3_CLK/4 - 0.08 tL3_CLK/4 - 0.08 -- tL3_CLK/4 + 1.00 -- tL3_CLK/4 + 1.16 -- tL3_CLK/4 + 1.00 -- tL3_CLK/4 + 1.16 -- tL3_CLK/4 + 1.32 tL3_CLK/4 + 1.32 -- -- 2.0 0.5 -- 0.5 -- 0.5 -- 1.5 -- 1.5 -- 1.5 -- -- -- tL3_CLK/4 + 0.08 tL3_CLK/4 + 0.08 -- 1.0 -- 1.0 -- 1.0 -- tL3DVEH tL3DXEH tL3CHDV tL3CHOV tL3CHDX tL3CHOX tL3CHDZ Max Min Max Min Max Min Max 1.0 -- 0.5 tL3_CLK/4 + 1.48 tL3_CLK/4 + 1.48 -- -- 2.0 ns ns ns ns ns ns ns ns 1, 5 2, 5 2, 5 3, 4, 5 4 3, 4, 5 4, 5 5 L3OH0 = 0, L3OH1 = 0 L3OH0 = 0, L3OH1 =1 L3OH0 = 1, L3OH1 = 0 L3OH0 = 1, L3OH1 = 1 Unit Notes Electrical and Thermal Characteristics MOTOROLA At recommended operating conditions. See Table 4. Parameter L3_CLK rise and fall time Setup times: Data and parity Input hold times: Data and parity Valid times: Data and parity Valid times: All other outputs Output hold times: Data and parity Output hold times: All other outputs MPC7455 RISC Microprocessor Hardware Specifications L3_CLK to high impedance: Data and parity 27 Table 13. L3 Bus Interface AC Timing Specifications for PB2 and Late Write SRAMs (continued) All Speed Grades 6 Symbol Min tL3CHOZ -- 2.0 -- 2.0 -- 2.0 -- Max Min Max Min Max Min Max 2.0 ns 5 L3OH0 = 0, L3OH1 = 0 L3OH0 = 0, L3OH1 =1 L3OH0 = 1, L3OH1 = 0 L3OH0 = 1, L3OH1 = 1 Unit Notes 28 At recommended operating conditions. See Table 4. Parameter Electrical and Thermal Characteristics L3_CLK to high impedance: All other outputs MPC7455 RISC Microprocessor Hardware Specifications Notes: 1. Rise and fall times for the L3_CLK output are measured from 20% to 80% of GVDD. 2. All input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising edge of the input L3_ECHO_CLKn (see Figure 10). Input timings are measured at the pins. 3. All output specifications are measured from the midpoint voltage of the rising edge of L3_CLKn to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50- load (see Figure 10). 4. tL3_CLK/4 is one-fourth the period of L3_CLKn. This parameter indicates that the specified output signal is actually launched by an internal clock delayed in phase by 90. Therefore, there is a frequency component to the output valid and output hold times such that the specified output signal will be valid for approximately one L3_CLK period starting three-fourths of a clock prior to the edge on which the SRAM will sample it and ending one-fourth of a clock period after the edge it will be sampled. 5. Timing behavior and characterization are currently being evaluated. 6. These configuration bits allow the AC timing of the L3 interface to be altered via software. L3OH0 = L2CR[12], L30H1 = L3CR[12]. Revisions of the MPC7455 not described by this document may implement these bits differently. See Section 1.11.1, "Part Numbers Fully Addressed by This Document," and Section 1.11.2, "Part Numbers Not Fully Addressed by This Document," for more information on which devices are addressed by this document. MOTOROLA Electrical and Thermal Characteristics Figure 11 shows the typical connection diagram for the MPC7455 interfaced to PB2 SRAMs, such as the Motorola MCM63R737, or late write SRAMs, such as the Motorola MCM63R836A. MPC7455 L3_ADDR[16:0] L3_CNTL[0] L3_CNTL[1] Denotes Receive (SRAM to MPC7455) Aligned Signals L3_ECHO_CLK[0] {L3_DATA[0:15], L3_DP[0:1]} L3_CLK[0] {L3_DATA[16:31], L3_DP[2:3]} L3_ECHO_CLK[1] SRAM 1 SA[16:0] SS L3_ECHO_CLK[2] {L3_DATA[32:47], L3_DP[4:5]} L3_CLK[1] {L3_DATA[48:63], L3_DP[6:7]} L3_ECHO_CLK[3] Note: 1. Or as recommended by SRAM manufacturer for single-ended clocking. SW ZZ G K GND GND GVDD/2 1 SRAM 0 SA[16:0] SS SW DQ[0:17] K DQ[18:36] ZZ G K GND GND GVDD/2 1 Denotes Transmit (MPC7455 to SRAM) Aligned Signals DQ[0:17] K DQ[18:36] Figure 11. Typical Synchronous 1-MByte L3 Cache Late Write or PB2 Interface MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 29 Electrical and Thermal Characteristics Figure 12 shows the L3 bus timing diagrams for the MPC7455 interfaced to PB2 or late write SRAMs. Outputs L3_CLK[0,1] L3_ECHO_CLK[1,3] tL3CHOV ADDR, L3_CNTL tL3CHOZ tL3CHDV L3DATA WRITE tL3CHDZ Inputs L3_ECHO_CLK[0,2] VM tL3DVEH tL3DXEH Parity Inputs L3 Data and Data VM = Midpoint Voltage (GVDD/2) tL3CHDX VM VM tL3CHOX Figure 12. L3 Bus Timing Diagrams for Late Write or PB2 SRAMs 1.5.2.5 IEEE 1149.1 AC Timing Specifications Table 14 provides the IEEE 1149.1 (JTAG) AC timing specifications as defined in Figure 14 through Figure 17. Table 14. JTAG AC Timing Specifications (Independent of SYSCLK) 1 At recommended operating conditions. See Table 4. Parameter TCK frequency of operation TCK cycle time TCK clock pulse width measured at 1.4 V TCK rise and fall times TRST assert time Input setup times: Boundary-scan data TMS, TDI Input hold times: Boundary-scan data TMS, TDI Symbol fTCLK t TCLK tJHJL tJR and tJF tTRST tDVJH tIVJH tDXJH tIXJH Min 0 30 15 0 25 4 0 20 25 Max 33.3 -- -- 2 -- -- -- Unit MHz ns ns ns ns ns Notes 2 3 ns -- -- 3 30 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Electrical and Thermal Characteristics Table 14. JTAG AC Timing Specifications (Independent of SYSCLK) 1 (continued) At recommended operating conditions. See Table 4. Parameter Valid times: Boundary-scan data TDO Output hold times: Boundary-scan data TDO TCK to output high impedance: Boundary-scan data TDO Symbol Min Max Unit ns Notes 4 tJLDV tJLOV tJLDX tJLOX tJLDZ tJLOZ 4 4 TBD TBD 3 3 20 25 ns TBD TBD ns 19 9 4, 5 4 Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of TCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50- load (see Figure 13). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 3. Non-JTAG signal input timing with respect to TCK. 4. Non-JTAG signal output timing with respect to TCK. 5. Guaranteed by design and characterization. Figure 13 provides the AC test load for TDO and the boundary-scan outputs of the MPC7455. Output Z0 = 50 OVDD/2 RL = 50 Figure 13. Alternate AC Test Load for the JTAG Interface Figure 14 provides the JTAG clock input timing diagram. TCLK VM tJHJL tTCLK VM = Midpoint Voltage (OVDD/2) VM VM tJR tJF Figure 14. JTAG Clock Input Timing Diagram Figure 15 provides the TRST timing diagram. TRST VM tTRST VM = Midpoint Voltage (OVDD/2) VM Figure 15. TRST Timing Diagram MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 31 Electrical and Thermal Characteristics Figure 16 provides the boundary-scan timing diagram. TCK VM tDVJH Boundary Data Inputs tJLDV tJLDX Boundary Data Outputs tJLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (OVDD/2) Output Data Valid Input Data Valid VM tDXJH Figure 16. Boundary-Scan Timing Diagram Figure 17 provides the test access port timing diagram. TCK VM tIVJH TDI, TMS tJLOV tJLOX TDO Output Data Valid Input Data Valid VM tIXJH tJLOZ TDO Output Data Valid VM = Midpoint Voltage (OVDD/2) Figure 17. Test Access Port Timing Diagram 32 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Pin Assignments 1.6 Pin Assignments Figure 18 (in Part A) shows the pinout of the MPC7445, 360 CBGA package as viewed from the top surface. Part B shows the side profile of the CBGA package to indicate the direction of the top surface view. Part A 1 A B C D E F G H J K L M N P R T U V W 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Not to Scale Part B Substrate Assembly Encapsulant View Die Figure 18. Pinout of the MPC7445, 360 CBGA Package as Viewed from the Top Surface MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 33 Pin Assignments Figure 19 (in Part A) shows the pinout of the MPC7455, 483 CBGA package as viewed from the top surface. Part B shows the side profile of the CBGA package to indicate the direction of the top surface view. Part A 1 A B C D E F G H J K L M N P R T U V W Y AA AB Not to Scale 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part B Substrate Assembly Encapsulant View Die Figure 19. Pinout of the MPC7455, 483 CBGA Package as Viewed from the Top Surface 34 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Pinout Listings 1.7 Pinout Listings NOTE This pinout is not compatible with the MPC750, MPC7400, or MPC7410, 360 BGA package. Table 15. Pinout Listing for the MPC7445, 360 CBGA Package Table 15 provides the pinout listing for the MPC7445, 360 CBGA package. Table 16 provides the pinout listing for the MPC7455, 483 CBGA package. Signal Name A[0:35] Pin Number E11, H1, C11, G3, F10, L2, D11, D1, C10, G2, D12, L3, G4, T2, F4, V1, J4, R2, K5, W2, J2, K4, N4, J3, M5, P5, N3, T1, V2, U1, N5, W1, B12, C4, G10, B11 R1 C1, E3, H6, F5, G7 N2 A8 M1 G9 F8 D2 B7 J1 A3 B1 H2 R15, W15, T14, V16, W16, T15, U15, P14, V13, W13, T13, P13, U14, W14, R12, T12, W12, V12, N11, N10, R11, U11, W11, T11, R10, N9, P10, U10, R9, W10, U9, V9, W5, U6, T5, U5, W7, R6, P7, V6, P17, R19, V18, R18, V19, T19, U19, W19, U18, W17, W18, T16, T18, T17, W3, V17, U4, U8, U7, R7, P6, R8, W8, T8 M2 T3, W4, T4, W9, M6, V3, N8, W6 R3 G1, K1, P1, N1 A11 E2 Active High I/O I/O I/F Select 1 BVSEL Notes 11 AACK AP[0:4] ARTRY AVDD BG BMODE0 BMODE1 BR BVSEL CI CKSTP_IN CKSTP_OUT CLK_OUT D[0:63] Low High Low -- Low Low Low Low High Low Low Low High High Input I/O I/O Input Input Input Input Output Input Output Input Output Output I/O BVSEL BVSEL BVSEL N/A BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL 1, 7 8 5 6 8 DBG DP[0:7] DRDY DTI[0:3] EXT_QUAL GBL Low High Low High High Low Input I/O Output Input Input I/O BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL 4 13 9 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 35 Pinout Listings Table 15. Pinout Listing for the MPC7445, 360 CBGA Package (continued) Signal Name GND Pin Number B5, C3, D6, D13, E17, F3, G17, H4, H7, H9, H11, H13, J6, J8, J10, J12, K7, K3, K9, K11, K13, L6, L8, L10, L12, M4, M7, M9, M11, M13, N7, P3, P9, P12, R5, R14, R17, T7, T10, U3, U13, U17, V5, V8, V11, V15 B2 D8 D4 G8 B3 A6, A13, A14, A15, A16, A17, A18, A19, B13, B14, B15, B16, B17, B18, B19, C13, C14, C15, C16, C17, C18, C19, D14, D15, D16, D17, D18, D19, E12, E13, E14, E15, E16, E19, F12, F13, F14, F15, F16, F17, F18, F19, G11, G12, G13, G14, G15, G16, G19, H14, H15, H16, H17, H18, H19, J14, J15, J16, J17, J18, J19, K15, K16, K17, K18, K19, L14, L15, L16, L17, L18, L19, M14, M15, M16, M17, M18, M19, N12, N13, N14, N15, N16, N17, N18, N19, P15, P16, P18, P19 E8 C9 B4, C2, C12, D5, E18, F2, G18, H3, J5, K2, L5, M3, N6, P2, P8, P11, R4, R13, R16, T6, T9, U2, U12, U16, V4, V7, V10, V14 B8, C8, C7, D7, A7 D9 A9 G5 P4 E4, H5 F9 A2 A10 K6 E1 F11 Active -- I/O -- I/F Select 1 N/A Notes HIT HRESET INT L1_TSTCLK L2_TSTCLK No Connect Low Low Low High High -- Output Input Input Input Input -- BVSEL BVSEL BVSEL BVSEL BVSEL -- 4 9 12 3 LSSD_MODE MCP OVDD Low Low -- Input Input -- BVSEL BVSEL N/A 2, 7 PLL_CFG[0:4] PMON_IN PMON_OUT QACK QREQ SHD[0:1] SMI SRESET SYSCLK TA TBEN TBST High Low Low Low Low Low Low Low -- Low High Low Input Input Output Input Output I/O Input Input Input Input Input Output BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL 8 10 36 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Pinout Listings Table 15. Pinout Listing for the MPC7445, 360 CBGA Package (continued) Signal Name TCK TDI TDO TEA TEST[0:3] TEST[4] TMS TRST TS TSIZ[0:2] TT[0:4] WT VDD C6 B9 A4 L1 A12, B6, B10, E10 D10 F1 A5 L4 G6, F7, E7 E5, E6, F6, E9, C5 D3 H8, H10, H12, J7, J9, J11, J13, K8, K10, K12, K14, L7, L9, L11, L13, M8, M10, M12 Pin Number Active High High High Low -- -- High Low Low High High Low -- I/O Input Input Output Input Input Input Input Input I/O Output I/O Output -- I/F Select 1 BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL N/A 8 2 9 7 7, 14 8 7 Notes Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals; and VDD supplies power to the processor core and the PLL (after filtering to become AVDD). To program the I/O voltage, connect BVSEL to either GND (selects 1.8 V) or to HRESET (selects 2.5 V). If used, the pulldown resistor should be less than 250 . For actual recommended value of Vin or supply voltages see Table 4. 2. These input signals are for factory use only and must be pulled up to OVDD for normal machine operation. 3. These signals are for factory use only and must be left unconnected for normal machine operation. 4. Ignored in 60x bus mode. 5. This signal selects between MPX bus mode (asserted) and 60x bus mode (negated) and will be sampled at HRESET going high. 6. This signal must be negated during reset, by pull-up to OVDD or negation by HRESET (inverse of HRESET), to ensure proper operation. 7. Internal pull-up on die. 8. These pins require weak pull-up resistors (for example, 4.7 k) to maintain the control signals in the negated state after they have been actively negated and released by the MPC7445 and other bus masters. 9. These input signals are for factory use only and must be pulled down to GND for normal machine operation. 10. This pin can externally cause a performance monitor event. Counting of the event is enabled via software. 11. Unused address pins must be pulled down to GND. 12. This test signal is recommended to be tied to HRESET; however, other configurations will not adversely affect performance. 13. These signals must be pulled down to GND if unused, or if the MPC7445 is in 60x bus mode. 14. This signal must be asserted during reset, by pull-down to GND or assertion by HRESET, to ensure proper operation. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 37 Pinout Listings Table 16. Pinout Listing for the MPC7455, 483 CBGA Package Signal Name A[0:35] Pin Number E10, N4, E8, N5, C8, R2, A7, M2, A6, M1, A10, U2, N2, P8, M8, W4, N6, U6, R5, Y4, P1, P4, R6, M7, N7, AA3, U4, W2, W1, W3, V4, AA1, D10, J4, G10, D9 U1 L5, L6, J1, H2, G5 T2 B2 R3 C6 C4 K1 G6 R1 F3 K6 N1 AB15, T14, R14, AB13, V14, U14, AB14, W16, AA11, Y11, U12, W13, Y14, U13, T12, W12, AB12, R12, AA13, AB11, Y12, V11, T11, R11, W10, T10, W11, V10, R10, U10, AA10, U9, V7, T8, AB4, Y6, AB7, AA6, Y8, AA7, W8, AB10, AA16, AB16, AB17, Y18, AB18, Y16, AA18, W14, R13, W15, AA14, V16, W6, AA12, V6, AB9, AB6, R7, R9, AA9, AB8, W9 V1 AA2, AB3, AB2, AA8, R8, W5, U8, AB5 T6 P2, T5, U3, P6 B9 M4 Active High I/O I/O I/F Select 1 BVSEL Notes 11 AACK AP[0:4] ARTRY AVDD BG BMODE0 BMODE1 BR BVSEL CI CKSTP_IN CKSTP_OUT CLK_OUT D[0:63] Low High Low -- Low Low Low Low High Low Low Low High High Input I/O I/O Input Input Input Input Output Input Output Input Output Output I/O BVSEL BVSEL BVSEL N/A BVSEL BVSEL BVSEL BVSEL N/A BVSEL BVSEL BVSEL BVSEL BVSEL 3, 7 8 5 6 8 DBG DP[0:7] DRDY DTI[0:3]) EXT_QUAL GBL Low High Low High High Low Input I/O Output Input Input I/O BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL 4 13 9 38 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Pinout Listings Table 16. Pinout Listing for the MPC7455, 483 CBGA Package (continued) Signal Name GND Pin Number A22, B1, B5, B12, B14, B16, B18, B20, C3, C9, C21, D7, D13, D15, D17, D19, E2, E5, E21, F10, F12, F14, F16, F19, G4, G7, G17, G21, H13, H15, H19, H5, J3, J10, J12, J14, J17, J21, K5, K9, K11, K13, K15, K19, L10, L12, L14, L17, L21, M3, M6, M9, M11, M13, M19, N10, N12, N14, N17, N21, P3, P9, P11, P13, P15, P19, R17, R21, T13, T15, T19, T4, T7, T9, U17, U21, V2, V5, V8, V12, V15, V19, W7, W17, W21, Y3, Y9, Y13, Y15, Y20, AA5, AA17, AB1, AB22 B13, B15, B17, B19, B21, D12, D14, D16, D18, D21, E19, F13, F15, F17, F21, G19, H12, H14, H17, H21, J19, K17, K21, L19, M17, M21, N19, P17, P21, R15, R19, T17, T21, U19, V17, V21, W19, Y21 K2 A3 J6 H4 J2 A4 F20, J16, E22, H18, G20, F22, G22, H20, K16, J18, H22, J20, J22, K18, K20, L16, K22, L18 V22, C17 L20, L22 AA19, AB20, U16, W18, AA20, AB21, AA21, T16, W20, U18, Y22, R16, V20, W22, T18, U20, N18, N20, N16, N22, M16, M18, M20, M22, R18, T20, U22, T22, R20, P18, R22, M15, G18, D22, E20, H16, C22, F18, D20, B22, G16, A21, G15, E17, A20, C19, C18, A19, A18, G14, E15, C16, A17, A16, C15, G13, C14, A14, E13, C13, G12, A13, E12, C12 AB19, AA22, P22, P16, C20, E16, A15, A12 V18, E18 P20, E14 F6 B8 A8, A11, B6, B11, C11, D11, D3, D5, E11, E7, F2, F11, G11, G2, H11, H9, J8 Active -- I/O -- I/F Select 1 N/A Notes GVDD -- -- N/A 15 HIT HRESET INT L1_TSTCLK L2_TSTCLK L3VSEL L3ADDR[17:0] Low Low Low High High High High Output Input Input Input Input Input Output BVSEL BVSEL BVSEL BVSEL BVSEL N/A L3VSEL 4 9 12 3, 7 L3_CLK[0:1] L3_CNTL[0:1] L3DATA[0:63] High Low High Output Output I/O L3VSEL L3VSEL L3VSEL L3DP[0:7] L3_ECHO_CLK[0,2] L3_ECHO_CLK[1,3] LSSD_MODE MCP No Connect High High HIgh Low Low -- I/O Input I/O Input Input -- L3VSEL L3VSEL L3VSEL BVSEL BVSEL N/A 16 2, 7 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 39 Pinout Listings Table 16. Pinout Listing for the MPC7455, 483 CBGA Package (continued) Signal Name OVDD Pin Number B3, C5, C7, C10, D2, E3, E9, F5, G3, G9, H7, J5, K3, L7, M5, N3, P7, R4, T3, U5, U7, U11, U15, V3, V9, V13, Y2, Y5, Y7, Y10, Y17, Y19, AA4, AA15 A2, F7, C2, D4, H8 E6 B4 K7 Y1 L4, L8 G8 G1 D6 N8 L3 B7 J7 E4 H1 T1 B10, H6, H10, D8, F9, F8 A9 K4 C1 P5 L1,H3,D1 F1, F4, K8, A5, E1 L2 Active -- I/O -- I/F Select 1 N/A Notes PLL_CFG[0:4] PMON_IN PMON_OUT QACK QREQ SHD[0:1] SMI SRESET SYSCLK TA TBEN TBST TCK TDI TDO TEA TEST[0:5] TEST[6] TMS TRST TS TSIZ[0:2] TT[0:4] WT High Low Low Low Low Low Low Low -- Low High Low High High High Low -- -- High Low Low High High Low Input Input Output Input Output I/O Input Input Input Input Input Output Input Input Output Input Input Input Input Input I/O Output I/O Output BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL BVSEL 8 2 9 7 7, 14 8 7 8 10 40 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Package Description Table 16. Pinout Listing for the MPC7455, 483 CBGA Package (continued) Signal Name VDD Pin Number J9, J11, J13, J15, K10, K12, K14, L9, L11, L13, L15, M10, M12, M14, N9, N11, N13, N15, P10, P12, P14 Active -- I/O -- I/F Select 1 N/A Notes Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals except the L3 cache controls (L3CTL[0:1]); GVDD supplies power to the L3 cache interface (L3ADDR[0:17], L3DATA[0:63], L3DP[0:7], L3_ECHO_CLK[0:3], and L3_CLK[0:1]) and the L3 control signals L3_CNTL[0:1]; and VDD supplies power to the processor core and the PLL (after filtering to become AVDD). For actual recommended value of Vin or supply voltages, see Table 4. 2. These input signals are for factory use only and must be pulled up to OVDD for normal machine operation. 3. To program the processor interface I/O voltage, connect BVSEL to either GND (selects 1.8 V) or to HRESET (selects 2.5 V). To program the L3 interface, connect L3VSEL to either GND (selects 1.8 V) or to HRESET (selects 2.5 V) or to HRESET (selects 1.5 V). If used, pulldown resistors should be less than 250 . 4. Ignored in 60x bus mode. 5. This signal selects between MPX bus mode (asserted) and 60x bus mode (negated) and will be sampled at HRESET going high. 6. This signal must be negated during reset, by pull-up to OVDD or negation by HRESET (inverse of HRESET), to ensure proper operation. 7. Internal pull-up on die. 8. These pins require weak pull-up resistors (for example, 4.7 k) to maintain the control signals in the negated state after they have been actively negated and released by the MPC7455 and other bus masters. 9. These input signals for factory use only and must be pulled down to GND for normal machine operation. 10. This pin can externally cause a performance monitor event. Counting of the event is enabled via software. 11. Unused address pins must be pulled down to GND. 12. This test signal is recommended to be tied to HRESET; however, other configurations will not adversely affect performance. 13. These signals must be pulled down to GND if unused or if the MPC7455 is in 60x bus mode. 14. This signal must be asserted during reset, by pull-down to GND or assertion by HRESET, to ensure proper operation. 15. Power must be supplied to GVDD, even when the L3 interface is disabled or unused. 16. These signals are for factory use only and must be left unconnected for normal machine operation. 1.8 1.8.1 Package Description Package Parameters for the MPC7445, 360 CBGA Package outline Interconnects Pitch Minimum module height Ball diameter 25 x 25 mm 360 (19 x 19 ball array - 1) 1.27 mm (50 mil) 2.72 mm 0.89 mm (35 mil) The following sections provide the package parameters and mechanical dimensions for the CBGA package. The package parameters are as provided in the following list. The package type is 25 x 25 mm, 360-lead ceramic ball grid array (CBGA). Maximum module height 3.24 mm MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 41 Package Description 1.8.2 Mechanical Dimensions for the MPC7445, 360 CBGA Figure 20 provides the mechanical dimensions and bottom surface nomenclature for the MPC7445, 360 CBGA package. 2X 0.2 D B Capacitor Region A1 CORNER D1 0.15 A A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. 1 E3 E2 E1 E Millimeters 2X DIM 0.2 C 1 2 3 4 5 6 7 8 9 10 11 1213141516 171819 W V U T R P N M L K J H G F E D C B A MIN 2.74 0.82 1.10 -- 0.82 MAX 3.20 1.00 1.30 0.6 0.93 D2 A A1 A2 A3 b A3 A2 A1 A D D1 D2 e E E1 E2 25.00 BSC -- 12.24 6.15 12.26 1.27 BSC 25.00 BSC -- 8.28 9.00 10.2 -- 9.20 e 360X b 0.3 A B C 0.15 A E3 Figure 20. Mechanical Dimensions and Bottom Surface Nomenclature for the MPC7445, 360 CBGA Package 42 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Package Description 1.8.3 Package Parameters for the MPC7455, 483 CBGA Package outline Interconnects Pitch Minimum module height Ball diameter 29 x 29 mm 483 (22 x 22 ball array - 1) 1.27 mm (50 mil) -- 0.89 mm (35 mil) The package parameters are as provided in the following list. The package type is 29 x 29 mm, 483-lead ceramic ball grid array (CBGA). Maximum module height 3.22 mm 1.8.4 Mechanical Dimensions for the MPC7455, 483 CBGA Figure 21 provides the mechanical dimensions and bottom surface nomenclature for the MPC7455, 483 CBGA package. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 43 Package Description 2X 0.2 D D1 A1 CORNER B D3 Capacitor Region A 0.15 A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. TOP SIDE A1 CORNER INDEX IS A METALIZED FEATURE WITH VARIOUS SHAPES. BOTTOM SIDE. A1 CORNER IS DESIGNATED WITH A BALL MISSING FROM THE ARRAY. D2 1 E3 E E2 E4 E1 Millimeters 2X DIM 0.2 C 1 2 3 4 5 6 7 8 9 10 11 1213141516 17 18 19 2021 22 AB AA Y W V U T R P N M L K J H G F E D C B A MIN 2.74 0.82 1.10 -0.82 MAX 3.20 1.00 1.30 0.60 0.93 D4 A A1 A2 A3 b D D1 A3 A2 A1 A 29.00 BSC -- 8.94 -- 12.24 11.6 -- 6.9 12.26 D2 D3 D4 e E E1 E2 E3 E4 1.27 BSC 29.00 BSC -- 8.94 -- 9.00 11.6 -- 6.9 9.20 e 483X b 0.3 A B C 0.15 A Figure 21. Mechanical Dimensions and Bottom Surface Nomenclature for the MPC7455, 483 CBGA Package 44 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information 1.9 System Design Information This section provides system and thermal design recommendations for successful application of the MPC7455. 1.9.1 PLL Configuration The MPC7455 PLL is configured by the PLL_CFG[0:4] signals. For a given SYSCLK (bus) frequency, the PLL configuration signals set the internal CPU and VCO frequency of operation. The PLL configuration for the MPC7455 is shown in Table 17 for a set of example frequencies. In this example, shaded cells represent settings that, for a given SYSCLK frequency, result in core and/or VCO frequencies that do not comply with the 1-GHz column in Table 8. Note that these configurations were different in devices prior to Rev F; see Section 1.11.2, "Part Numbers Not Fully Addressed by This Document," for more information regarding documentation of prior revisions. Table 17. MPC7455 Microprocessor PLL Configuration Example for 1.0 GHz Parts Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz) PLL_ CFG[0:4] Bus-toCore Multiplier 2x 3x 4x 5x 5.5x 6x 6.5x 7x 7.5x 8x 8.5x 9x Core-toVCO Multiplier 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 500 (1000) 533 (1066) 566 (1132) 600 (1200) 525 (1050) 563 (1125) 600 (1200) 638 (1276) 675 (1350) 540 (1080) 580 (1160) 623 (1245) 664 (1328) 706 (1412) 747 (1494) 500 (1000) 550 (1100) 600 (1200) 650 (1300) 700 (1400) 750 (1500) 800 (1600) 850 (1700) 900 (1800) 532 (1064) 667 (1333) 733 (1466) 800 (1600) 866 (1730) 931 (1862) 1000 (2000) Bus (SYSCLK) Frequency 33.3 MHz 50 MHz 66.6 MHz 75 MHz 83 MHz 100 MHz 133 MHz 01000 10000 10100 10110 10010 11010 01010 00100 00010 11000 01100 01111 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 45 System Design Information Table 17. MPC7455 Microprocessor PLL Configuration Example for 1.0 GHz Parts (continued) Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz) PLL_ CFG[0:4] Bus-toCore Multiplier 9.5x 10x 10.5x 11x 11.5x 12x 12.5x 13x 13.5x 14x 15x 16x 17x 18x 20x 21x 24x 28x Core-toVCO Multiplier 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 2x 500 (1000) 533 (1066) 566 (1132) 600 (1200) 667 (1334) 700 (1400) 800 (1600) 933 (1866) PLL off, SYSCLK clocks core circuitry directly 500 (1000) 525 (1050) 550 (1100) 575 (1150) 600 (1200) 600 (1200) 650 (1300) 675 (1350) 700 (1400) 750 (1500) 800 (1600) 850 (1900) 900 (1800) 1000 (2000) Bus (SYSCLK) Frequency 33.3 MHz 50 MHz 66.6 MHz 633 (1266) 667 (1333) 700 (1400) 733 (1466) 766 (532) 800 (1600) 833 (1666) 865 (1730) 900 (1800) 933 (1866) 1000 (2000) 75 MHz 712 (1524) 750 (1500) 938 (1876) 825 (1650) 863 (1726) 900 (1800) 938 (1876) 975 (1950) 83 MHz 789 (1578) 830 (1660) 872 (1744) 913 (1826) 955 (1910) 996 (1992) 100 MHz 950 (1900) 1000 (2000) 133 MHz 01110 10101 10001 10011 00000 10111 11111 01011 11100 11001 00011 11011 00001 00101 00111 01001 01101 11101 00110 PLL bypass 46 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information Table 17. MPC7455 Microprocessor PLL Configuration Example for 1.0 GHz Parts (continued) Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz) PLL_ CFG[0:4] Bus-toCore Multiplier Core-toVCO Multiplier Bus (SYSCLK) Frequency 33.3 MHz 50 MHz 66.6 MHz 75 MHz 83 MHz 100 MHz 133 MHz 11110 PLL off PLL off, no core clocking occurs Notes: 1. PLL_CFG[0:4] settings not listed are reserved. 2. The sample bus-to-core frequencies shown are for reference only. Some PLL configurations may select bus, core, or VCO frequencies which are not useful, not supported, or not tested for by the MPC7455; see Section 1.5.2.1, "Clock AC Specifications," for valid SYSCLK, core, and VCO frequencies. 3. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly and the PLL is disabled. However, the bus interface unit requires a 2x clock to function. Therefore, an additional signal, EXT_QUAL, must be driven at one-half the frequency of SYSCLK and offset in phase to meet the required input setup tIVKH and hold time tIXKH (see Table 9). The result will be that the processor bus frequency will be one-half SYSCLK while the internal processor is clocked at SYSCLK frequency. This mode is intended for factory use and emulator tool use only. Note: The AC timing specifications given in this document do not apply in PLL-bypass mode. 4. In PLL-off mode, no clocking occurs inside the MPC7455 regardless of the SYSCLK input. The MPC7455 generates the clock for the external L3 synchronous data SRAMs by dividing the core clock frequency of the MPC7455. The core-to-L3 frequency divisor for the L3 PLL is selected through the L3_CLK bits of the L3CR register. Generally, the divisor must be chosen according to the frequency supported by the external RAMs, the frequency of the MPC7455 core, and timing analysis of the circuit board routing. Table 18 shows various example L3 clock frequencies that can be obtained for a given set of core frequencies. Table 18. Sample Core-to-L3 Frequencies Core Frequency (MHz) 500 533 550 600 6502 6662 7002 7332 8002 8672 9332 /2 250 266 275 300 325 333 350 367 400 433 467 /2.5 200 213 220 240 260 266 280 293 320 347 373 /3 167 178 183 200 217 222 233 244 266 289 311 /3.5 143 152 157 171 186 190 200 209 230 248 266 /4 125 133 138 150 163 167 175 183 200 217 233 /5 100 107 110 120 130 133 140 147 160 173 187 /6 83 89 92 100 108 111 117 122 133 145 156 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 47 System Design Information Table 18. Sample Core-to-L3 Frequencies (continued) Core Frequency (MHz) 10002 /2 500 /2.5 400 /3 333 /3.5 285 /4 250 /5 200 /6 166 Notes: 1. The core and L3 frequencies are for reference only. Note that maximum L3 frequency is design dependent. Some examples may represent core or L3 frequencies which are not useful, not supported, or not tested for the MPC7455; see Section 1.5.2.3, "L3 Clock AC Specifications," for valid L3_CLK frequencies and for more information regarding the maximum L3 frequency. Shaded cells do not comply with Table 10. 2. These core frequencies are not supported by all speed grades; see Table 8. 1.9.2 PLL Power Supply Filtering The AVDD power signal is provided on the MPC7455 to provide power to the clock generation PLL. To ensure stability of the internal clock, the power supplied to the AVDD input signal should be filtered of any noise in the 500 kHz to 10 MHz resonant frequency range of the PLL. A circuit similar to the one shown in Figure 22 using surface mount capacitors with minimum effective series inductance (ESL) is recommended. The circuit should be placed as close as possible to the AVDD pin to minimize noise coupled from nearby circuits. It is often possible to route directly from the capacitors to the AVDD pin, which is on the periphery of the 360 CBGA footprint and very close to the periphery of the 483 CBGA footprint, without the inductance of vias. 10 VDD 2.2 F 2.2 F Low ESL Surface Mount Capacitors GND AVDD Figure 22. PLL Power Supply Filter Circuit 1.9.3 Decoupling Recommendations Due to the MPC7455 dynamic power management feature, large address and data buses, and high operating frequencies, the MPC7455 can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC7455 system, and the MPC7455 itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, OVDD, and GVDD pin of the MPC7455. It is also recommended that these decoupling capacitors receive their power from separate VDD, OVDD/GVDD, and GND power planes in the PCB, utilizing short traces to minimize inductance. These capacitors should have a value of 0.01 or 0.1 F. Only ceramic surface mount technology (SMT) capacitors should be used to minimize lead inductance, preferably 0508 or 0603 orientations where connections are made along the length of the part. Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993) and contrary to previous recommendations for decoupling Motorola microprocessors, multiple small capacitors of equal value are recommended over using multiple values of capacitance. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, GVDD, and OVDD planes, to enable quick recharging of the smaller chip capacitors. These 48 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information bulk capacitors should have a low equivalent series resistance (ESR) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors: 100-330 F (AVX TPS tantalum or Sanyo OSCON). 1.9.4 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. Unused active low inputs should be tied to OVDD. Unused active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Power and ground connections must be made to all external VDD, OVDD, GVDD, and GND pins in the MPC7455. If the L3 interface is not used, GVDD should be connected to the OVDD power phase, and L3VSEL should be connected to BVSEL. 1.9.5 Output Buffer DC Impedance The MPC7455 processor bus and L3 I/O drivers are characterized over process, voltage, and temperature. To measure Z0, an external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 23). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the pad equals OVDD/2. RN then becomes the resistance of the pull-down devices. When data is held high, SW1 is closed (SW2 is open), and RP is trimmed until the voltage at the pad equals OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. OVDD RN SW2 Data Pad SW1 RP OGND Figure 23. Driver Impedance Measurement Table 19 summarizes the signal impedance results. The impedance increases with junction temperature and is relatively unaffected by bus voltage. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 49 System Design Information Table 19. Impedance Characteristics VDD = 1.5 V, OVDD = 1.8 V 5%, Tj = 5-85C Impedance Z0 Typical Maximum Processor Bus 33-42 31-51 L3 Bus 34-42 32-44 Unit 1.9.6 Pull-Up/Pull-Down Resistor Requirements The MPC7455 requires high-resistive (weak: 4.7-k) pull-up resistors on several control pins of the bus interface to maintain the control signals in the negated state after they have been actively negated and released by the MPC7455 or other bus masters. These pins are: TS, ARTRY, SHDO, and SHD1. Some pins designated as being for factory test must be pulled up to OVDD or down to GND to ensure proper device operation. For the MPC7445, 360 BGA, the pins that must be pulled up to OVDD are: LSSD_MODE and TEST[0:3]; the pins that must be pulled down to GND are: L1_TSTCLK and TEST[4]. For the MPC7455, 483 BGA, the pins that must be pulled up to OVDD are: LSSD_MODE and TEST[0:5]; the pins that must be pulled down are: L1_TSTCLK and TEST[6]. In addition, the MPC7455 has one open-drain style output that requires a pull-up resistor (weak or stronger: 4.7-1 k) if it is used by the system. This pin is CKSTP_OUT. If pull-down resistors are used to configure BVSEL or L3VSEL, the resistors should be less than 250 (see Table 16). During inactive periods on the bus, the address and transfer attributes may not be driven by any master and may, therefore, float in the high-impedance state for relatively long periods of time. Because the MPC7455 must continually monitor these signals for snooping, this float condition may cause excessive power draw by the input receivers on the MPC7455 or by other receivers in the system. It is recommended that these signals be pulled up through weak (4.7-k) pull-up resistors by the system, or that they may be otherwise driven by the system during inactive periods of the bus. The snooped address and transfer attribute inputs are: A[0:35], AP[0:4], TT[0:4], CI, WT, and GBL. If extended addressing is not used, A[0:3] are unused and must be pulled low to GND through weak pull-down resistors. If the MPC7455 is in 60x bus mode, DTI[0:3] must be pulled low to GND through weak pull-down resistors. The data bus input receivers are normally turned off when no read operation is in progress and, therefore, do not require pull-up resistors on the bus. Other data bus receivers in the system, however, may require pull-ups, or that those signals be otherwise driven by the system during inactive periods by the system. The data bus signals are: D[0:63] and DP[0:7]. If address or data parity is not used by the system, and the respective parity checking is disabled through HID0, the input receivers for those pins are disabled, and those pins do not require pull-up resistors and should be left unconnected by the system. If all parity generation is disabled through HID0, then all parity checking should also be disabled through HID0, and all parity pins may be left unconnected by the system. The L3 interface does not normally require pull-up resistors. 1.9.7 JTAG Configuration Signals Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture. 50 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset performance will be obtained if the TRST signal is asserted during power-on reset. Because the JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying TRST to HRESET is not practical. The COP function of these processors allows a remote computer system (typically, a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP interface connects primarily through the JTAG port of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged into these signals with logic. The arrangement shown in Figure 24 allows the COP port to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not be used, TRST should be tied to HRESET through a 0- isolation resistor so that it is asserted when the system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during power-on. While Motorola recommends that the COP header be designed into the system as shown in Figure 24, if this is not possible, the isolation resistor will allow future access to TRST in the case where a JTAG interface may need to be wired onto the system in debug situations. The COP header shown in Figure 24 adds many benefits--breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features are possible through this interface--and can be as inexpensive as an unpopulated footprint for a header to be added when needed. The COP interface has a standard header for connection to the target system, based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector key. There is no standardized way to number the COP header shown in Figure 24; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 24 is common to all known emulators. The QACK signal shown in Figure 24 is usually connected to the PCI bridge chip in a system and is an input to the MPC7455 informing it that it can go into the quiescent state. Under normal operation this occurs during a low-power mode selection. In order for COP to work, the MPC7455 must see this signal asserted (pulled down). While shown on the COP header, not all emulator products drive this signal. If the product does not, a pull-down resistor can be populated to assert this signal. Additionally, some emulator products implement open-drain type outputs and can only drive QACK asserted; for these tools, a pull-up resistor can be implemented to ensure this signal is de-asserted when it is not being driven by the tool. Note that the pull-up and pull-down resistors on the QACK signal are mutually exclusive and it is never necessary to populate both in a system. To preserve correct power-down operation, QACK should be merged via logic so that it also can be driven by the PCI bridge. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 51 System Design Information From Target Board Sources (if any) SRESET SRESET HRESET QACK 13 11 HRESET SRESET 10 k 10 k 10 k 10 k 05 OVDD OVDD OVDD OVDD HRESET 1 3 5 7 9 11 2 4 6 8 10 12 KEY TRST 4 6 5 1 TRST OVDD OVDD CHKSTP_OUT 10 k 10 k OVDD OVDD CHKSTP_IN TMS VDD_SENSE 2 k CHKSTP_OUT 10 k 15 Key 14 2 13 No Pin CHKSTP_IN COP Header 8 TMS 9 1 3 7 2 10 12 16 QACK NC NC 2 k 3 10 k 4 TDO TDI TCK 15 16 COP Connector Physical Pin Out TDO TDI TCK QACK OVDD Notes: 1. RUN/STOP, normally found on pin 5 of the COP header, is not implemented on the MPC7455. Connect pin 5 of the COP header to OVDD with a 10-k pull-up resistor. 2. Key location; pin 14 is not physically present on the COP header. 3. Component not populated. Populate only if debug tool does not drive QACK. 4. Populate only if debug tool uses an open-drain type output and does not actively de-assert QACK. 5. If the JTAG interface is implemented, connect HRESET from the target source to TRST from the COP header though an AND gate to TRST of the part. If the JTAG interface is not implemented, connect HRESET from the target source to TRST of the part through a 0- isolation reisistor. Figure 24. JTAG Interface Connection 52 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information 1.9.8 Thermal Management Information This section provides thermal management information for the ceramic ball grid array (CBGA) package for air-cooled applications. Proper thermal control design is primarily dependent on the system-level design--the heat sink, airflow, and thermal interface material. To reduce the die-junction temperature, heat sinks may be attached to the package by several methods--spring clip to holes in the printed-circuit board or package, and mounting clip and screw assembly (see Figure 25); however, due to the potential large mass of the heat sink, attachment through the printed-circuit board is suggested. If a spring clip is used, the spring force should not exceed 10 pounds. Heat Sink Heat Sink Clip CBGA Package Thermal Interface Material Printed-Circuit Board Figure 25. Package Exploded Cross-Sectional View with Several Heat Sink Options The board designer can choose between several types of heat sinks to place on the MPC7455. There are several commercially available heat sinks for the MPC7455 provided by the following vendors: Aavid Thermalloy 80 Commercial St. Concord, NH 03301 Internet: www.aavidthermalloy.com Alpha Novatech 473 Sapena Ct. #15 Santa Clara, CA 95054 Internet: www.alphanovatech.com International Electronic Research Corporation (IERC) 413 North Moss St. Burbank, CA 91502 Internet: www.ctscorp.com Tyco Electronics Chip CoolersTM P.O. Box 3668 Harrisburg, PA 17105-3668 Internet: www.chipcoolers.com 603-224-9988 408-749-7601 818-842-7277 800-522-6752 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 53 System Design Information Wakefield Engineering 33 Bridge St. Pelham, NH 03076 Internet: www.wakefield.com 603-635-5102 Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. 1.9.8.1 Internal Package Conduction Resistance For the exposed-die packaging technology, shown in Table 3, the intrinsic conduction thermal resistance paths are as follows: * * The die junction-to-case (actually top-of-die since silicon die is exposed) thermal resistance The die junction-to-ball thermal resistance Figure 26 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. External Resistance Radiation Convection Heat Sink Thermal Interface Material Internal Resistance Die/Package Die Junction Package/Leads Printed-Circuit Board External Resistance Radiation Convection (Note the internal versus external package resistance.) Figure 26. C4 Package with Heat Sink Mounted to a Printed-Circuit Board Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink attach material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection. Because the silicon thermal resistance is quite small, for a first-order analysis, the temperature drop in the silicon may be neglected. Thus, the thermal interface material and the heat sink conduction/convective thermal resistances are the dominant terms. 1.9.8.2 Thermal Interface Materials A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 27 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. 54 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information The use of thermal grease significantly reduces the interface thermal resistance. That is, the bare joint results in a thermal resistance approximately seven times greater than the thermal grease joint. Often, heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see Figure 25). Therefore, the synthetic grease offers the best thermal performance, considering the low interface pressure and is recommended due to the high power dissipation of the MPC7455. Of course, the selection of any thermal interface material depends on many factors--thermal performance requirements, manufacturability, service temperature, dielectric properties, cost, etc. 2 Silicone Sheet (0.006 in.) Bare Joint Floroether Oil Sheet (0.007 in.) Graphite/Oil Sheet (0.005 in.) Synthetic Grease Specific Thermal Resistance (K-in.2/W) 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Contact Pressure (psi) Figure 27. Thermal Performance of Select Thermal Interface Material The board designer can choose between several types of thermal interface. Heat sink adhesive materials should be selected based on high conductivity, yet adequate mechanical strength to meet equipment shock/vibration requirements. There are several commercially available thermal interfaces and adhesive materials provided by the following vendors: The Bergquist Company 18930 West 78th St. Chanhassen, MN 55317 Internet: www.bergquistcompany.com Chomerics, Inc. 77 Dragon Ct. Woburn, MA 01888-4014 Internet: www.chomerics.com 800-347-4572 781-935-4850 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 55 System Design Information Dow-Corning Corporation Dow-Corning Electronic Materials 2200 W. Salzburg Rd. Midland, MI 48686-0997 Internet: www.dow.com Shin-Etsu MicroSi, Inc. 10028 S. 51st St. Phoenix, AZ 85044 Internet: www.microsi.com Thermagon Inc. 4707 Detroit Ave. Cleveland, OH 44102 Internet: www.thermagon.com 800-248-2481 888-642-7674 888-246-9050 The following section provides a heat sink selection example using one of the commercially available heat sinks. 1.9.8.3 Heat Sink Selection Example Tj = Ta + Tr + (RJC + Rint + Rsa) x Pd For preliminary heat sink sizing, the die-junction temperature can be expressed as follows: where: Tj is the die-junction temperature Ta is the inlet cabinet ambient temperature Tr is the air temperature rise within the computer cabinet RJC is the junction-to-case thermal resistance Rint is the adhesive or interface material thermal resistance Rsa is the heat sink base-to-ambient thermal resistance Pd is the power dissipated by the device During operation, the die-junction temperatures (Tj) should be maintained less than the value specified in Table 4. The temperature of air cooling the component greatly depends on the ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air temperature (Ta) may range from 30 to 40C. The air temperature rise within a cabinet (Tr) may be in the range of 5 to 10C. The thermal resistance of the thermal interface material (Rint) is typically about 1.5C/W. For example, assuming a Ta of 30C, a Tr of 5C, a CBGA package RJC = 0.1, and a typical power consumption (Pd) of 15.0 W, the following expression for Tj is obtained: Die-junction temperature: Tj = 30C + 5C + (0.1C/W + 1.5C/W + Rsa) x 15 W For this example, a Rsa value of 3.1C/W or less is required to maintain the die-junction temperature below the maximum value of Table 4. Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common figure-of-merit used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final die-junction operating temperature is not only a function of the component-level thermal resistance, but the system-level design and its operating conditions. In addition to the component's power consumption, a number of factors 56 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA System Design Information affect the final operating die-junction temperature--airflow, board population (local heat flux of adjacent components), heat sink efficiency, heat sink attach, heat sink placement, next-level interconnect technology, system air temperature rise, altitude, etc. Due to the complexity and the many variations of system-level boundary conditions for today's microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection, and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models for the board, as well as system-level designs. For system thermal modeling, the MPC7445 and MPC7455 thermal model is shown in Figure 28. Four volumes will be used to represent this device. Two of the volumes, solder ball, and air and substrate, are modeled using the package outline size of the package. The other two, die, and bump and underfill, have the same size as the die. Dimensions for these volumes for the MPC7445 and MPC7455 are given in Figure 20 and Figure 21, respectively. The silicon die should be modeled 9.10 x 12.25 x 0.74 mm with the heat source applied as a uniform source at the bottom of the volume. The bump and underfill layer is modeled as 9.10 x 12.25 x 0.069 mm (or as a collapsed volume) with orthotropic material properties: 0.6 W/(m * K) in the xy-plane and 2 W/(m * K) in the direction of the z-axis. The substrate volume is 25 x 25 x 1.2 mm (MPC7445) or 29 x 29 x 1.2 mm (MPC7455), and this volume has 18 W/(m * K) isotropic conductivity. The solder ball and air layer is modeled with the same horizontal dimensions as the substrate and is 0.9 mm thick. It can also be modeled as a collapsed volume using orthotropic material properties: 0.034 W/(m * K) in the xy-plane direction and 3.8 W/(m * K) in the direction of the z-axis. Die z Conductivity Value Bump and Underfill Side View of Model (Not to Scale) kx ky kz 0.6 0.6 2 Substrate Substrate k 18 Solder Ball and Air kx ky kz 0.034 0.034 3.8 y Top View of Model (Not to Scale) Die W/(m * K) x Unit Bump and Underfill Substrate Solder and Air Figure 28. Recommended Thermal Model of MPC7445 and MPC7455 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 57 Document Revision History 1.10 Document Revision History Table 20 provides a revision history for this hardware specification. Table 20. Document Revision History Rev. No. 0 1 Initial release. Updated for Rev F devices; information specific to Rev C devices is now documented in a separate part number specifications; see Section 1.11.2 for more information. Removed 600 and 800 MHz speed grades. Increased leakage current specifications in Table 6 from 10 to 30 A. Changed core voltage to 1.3 V; all instances of VDD and AVDD updated. Updated power consumption specifications in Table 7. Reduced I/O power guidance in Table 7 from <20% to <5%. Added footnote 1 to Figures 9 and 11. Removed CI and WT from Input Setup and Input Hold lists in Table 10; these are output-only signals. Removed INT, HRESET, MCP, SRESET, and SMI from Input Setup and Input Hold lists in Table 10; these are asynchronous inputs. Added TT[0:3] to Input Setup, Input Hold, Output Valid, and Output Hold lists in Table 10; these were mistakenly omitted in Rev 0. Updated Tables 13 and 14 to reflect new L3 AC timing in Rev F devices. Corrected Note 10 in Tables 16 and 17; this is an event pin, not an enable pin. Corrected entries for L3_ECHO_CLK[1,3] in Table 17; these are I/O pins, not input-only. Added Note 16 to Table 17; all No Connect pins must be left unconnected. Changed name of PLL_EXT to PLL_CFG[4] and updated all instances. Updated Table 18 to reflect PLL configuration settings for Rev F devices. Added dimensions D2 and E3 to Figure 20. Transposed dimensions D4 and E4 in Figure 21 (dimensions were reversed). Revised Figure 24 and Section 1.9.7. Revised format of Section 1.11.2 and added Tables 23 through 26. Revised Section 1.9.8.3 and added additional thermal modeling information, including Figure 28. Changed maximum heat sink clip spring force in Section 1.9.8, from 5.5 lbs to 10 lbs. Changed substrate marking for MPC7445 in Figure 29; all MPC744x device substrates are marked MPC7440. Changed substrate marking for MPC7455 in Figure 29; all MPC745x device substrates are marked MPC7450. 1.1 Removed reference to Note 4 for DTI signals in Tables 15 and 16: these signals are unused in 60x bus mode and must be pulled down (see Note 13); they are not ignored. Improved precision of die and package dimensions in Figures 20 and 21. Substantive Change(s) 58 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Document Revision History Table 20. Document Revision History (continued) Rev. No. 2 Substantive Change(s) Corrected entries in Table 17 for 33 MHz and 50 MHz bus frequencies with multipliers of 24x and higher. Corrected typographical errors in heatsink selection example in Section 1.9.8.3. Removed erroneous instances of PLL_EXT signal name and changed remaining instances of PLL_CFG[0:3] to PLL_CFG[0:4]. (These were artifacts from older revisions; see entry for Rev 1.0.) Corrected erroneous instances (artifacts) mentioning 1.6 V core voltage. Core voltage for devices completely covered by this revision (and revisions 1.x) of this document is 1.3 V. Corrected errors in PLL multipliers in Table 17: 32x and 25x are not supported ratios, 3x and 4x are supported, 10.5x and 12.5x PLL settings were incorrect. Replaced notes at bottom of Table 17 (erroneously missing in revisions 1.x). Updated coplanarity specifications in Figures 20 and 21 from 0.2 mm to 0.15 mm. MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 59 Ordering Information 1.11 Ordering Information Ordering information for the parts fully covered by this specification document is provided in Section 1.11.1, "Part Numbers Fully Addressed by This Document." Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Motorola sales office. In addition to the processor frequency, the part numbering scheme also includes an application modifier which may specify special application conditions. Each part number also contains a revision level code which refers to the die mask revision number. Section 1.11.2, "Part Numbers Not Fully Addressed by This Document," lists the part numbers which do not fully conform to the specifications of this document. These special part numbers require an additional document called a part number specification. 1.11.1 Part Numbers Fully Addressed by This Document Table 21 provides the Motorola part numbering nomenclature for the MPC7455. Table 21. Part Numbering Nomenclature XC Product Code XC 2 74x5 x RX Package RX = CBGA nnnn Processor Frequency 1 733 867 933 1000 x Application Modifier L: 1.3 V 50 mV 0 to 105C x Revision Level F: 3.3; PVR = 8001 0303 Part Process Identifier Descriptor 7455 7445 A Notes: 1. Processor core frequencies supported by parts addressed by this specification only. Parts addressed by part number specifications may support other maximum core frequencies. 2. The X prefix in a Motorola part number designates a "Pilot Production Prototype" as defined by Motorola SOP 3-13. These are from a limited production volume of prototypes manufactured, tested, and Q.A. inspected on a qualified technology to simulate normal production. These parts have only preliminary reliability and characterization data. Before pilot production prototypes may be shipped, written authorization from the customer must be on file in the applicable sales office acknowledging the qualification status and the fact that product changes may still occur while shipping pilot production prototypes. 1.11.2 Part Numbers Not Fully Addressed by This Document Parts with application modifiers or revision levels not fully addressed in this specification document are described in separate part number specifications which supplement and supersede this document; see Table 22 through Table 25. 60 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Ordering Information Table 22. Part Numbers Addressed by XPC74x5RXnnnLC Series Part Number Specification (Document Order No. MPC7455RXLCPNS/D) XPC Product Code XPC 74x5 Part Identifier 7455 7445 RX Package RX = CBGA nnn Processor Frequency 600 733 800 867 933 1000 L Application Modifier L: 1.6 V 50 mV 0 to 105C C Revision Level C: 2.1; PVR = 8001 0201 PPC Table 23. Part Numbers Addressed by XPC74x5RXnnnNx Series Part Number Specification (Document Order No. MPC7455RXNXPNS/D) XPC Product Code XPC 74x5 Part Identifier 7455 7445 RX Package RX = CBGA nnn Processor Frequency 600 733 800 N Application Modifier N: 1.3 V 50 mV 0 to 105C C Revision Level C: 2.1; PVR = 8001 0201 Table 24. Part Numbers Addressed by XPC74x5RXnnnPx Series Part Number Specification (Document Order No. MPC7455RXPXPNS/D) XPC Product Code XPC 7455 Part Identifier 7455 RX Package RX = CBGA nnn Processor Frequency 933 1000 P Application Modifier P: 1.85 V 50 mV 0 to 65C C Revision Level C: 2.1; PVR = 8001 0201 Table 25. Part Numbers Addressed by XPC74x5RXnnnSx Series Part Number Specification (Document Order No. MPC7455RXSXPNS/D) XPC Product Code XPC 7455 Part Identifier 7455 RX Package RX = CBGA nnnn Processor Frequency 1000 S Application Modifier S: 1.85 V 50 mV 0 to 75C C Revision Level C: 2.1; PVR = 8001 0201 MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 61 Ordering Information 1.11.3 Part Marking Parts are marked as the example shown in Figure 29. XC7445A RX1000LF MMMMMM ATWLYYWWA XC7455A RX1000LF MMMMMM ATWLYYWWA 7440 7450 BGA BGA Notes: MMMMMM is the 6-digit mask number. ATWLYYWWA is the traceability code. CCCCC is the country of assembly. This space is left blank if parts are assembled in the United States. Figure 29. Part Marking for BGA Device 62 MPC7455 RISC Microprocessor Hardware Specifications MOTOROLA Ordering Information THIS PAGE INTENTIONALLY LEFT BLANK MOTOROLA MPC7455 RISC Microprocessor Hardware Specifications 63 HOW TO REACH US: USA/EUROPE/LOCATIONS NOT LISTED: Motorola Literature Distribution P.O. Box 5405, Denver, Colorado 80217 1-303-675-2140 or (800) 441-2447 JAPAN: Motorola Japan Ltd. SPS, Technical Information Center 3-20-1, Minami-Azabu Minato-ku Tokyo 106-8573 Japan 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd. Silicon Harbour Centre, 2 Dai King Street Tai Po Industrial Estate, Tai Po, N.T., Hong Kong 852-26668334 TECHNICAL INFORMATION CENTER: (800) 521-6274 HOME PAGE: www.motorola.com/semiconductors Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. digital dna is a trademark of Motorola, Inc. All other product or service names are the property of their respective owners. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. (c) Motorola, Inc. 2003 MPC7455EC/D |
Price & Availability of MPC7455ED
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |